valutazioni - 6, GPA: 3.5
(
)
)
|
Facilità d'uso
Turn the steam/hot water knob in a clockwise direction to close. 3 The unit is now ready to make coffee. to boil water for other drinks, eg tea, fruit drinks. 1Make sure the selector knob is in the off position ( ). 2 Check that there is water in the tank. 3Turn the selector knob to the boiler position ( ). 4 Position a container under the hot water/steam nozzle. 5 When the OK light glows, turn the steam/hot water knob in an anti-clockwise direction then the selector knob to the coffee/hot water position ( ). Hot water will come out of the steam nozzle. 6To stop the flow of hot water return the selector knob to the off position ( ) then turn the steam/hot water knob in a clockwise direction. Do not dispense hot water from the steam nozzle for longer than 20 seconds in one operation. cleaning . Before cleaning, unplug and let everything cool. . Never immerse the appliance in water. . Don’t wash parts in the dishwasher. tank, lid, filter holder . Wash, rinse and allow to dry. filter (one and two cup version) . Wash and dry after every use. . After approximately every 100 uses dismantle and clean more thoroughly as described below. . Remove the cap located on the underside of the filter by turning in the direction indicated . Remove the crema device by pushing up from the underside . Separate the components of the crema device by pulling the gasket to the side and removing the plastic disc and metal filter . Rinse parts thoroughly. Clean the metal filter in hot water using a brush . Make sure the holes in the metal filter are not blocked. If necessary clean with a pin . Dry the parts then reassemble, making sure the parts are correctly assembled. steam/hot water nozzle . Prior to cleaning allow some hot water to flow out of the nozzle (see ‘to boil water for other drinks’) but unplug and allow to cool before proceeding. . Unscrew the nozzle by turning clockwise, then wash thoroughly. Check that the three holes in the nozzle are not blocked . If necessary unblock them with a pin. . Clean the steam/hot water delivery tube. Make sure the end is not blocked. . Screw the nozzle back onto the delivery tube. cup stand, drip tray . Empty the drip tray regularly. You’ll know when it is full, the red float in the middle of the drip tray will rise and become visible in the centre hole on the cup stand. 1Wash then dry. 3 liquid coffee outlet/boiler unit . Wipe away any coffee grounds from this area. At least twice a year carry out the following procedure:1 Using a screwdriver , unscrew the screw that holds the outlet of the boiler in place. 2 Clean the boiler area with a damp cloth. 3 Clean the removed outlet thoroughly in hot soapy water using a brush. Rinse thoroughly. Make sure the holes are not blocked, if necessary use a pin to clean. 4 Reverse the above procedure to re fit to the outlet. Failure to clean the boiler outlet and the filters as described invalidates the guarantee. descaling It is advisable to discale the coffee maker after 200 cups of coffee have been made. 1We recommend purchasing a specific product for descaling espresso coffee machines. 2Make sure the filter holder is not attached and position a bowl under the liquid coffee/boiler outlet. 3 Pour 1 litre water and 250ml descaler into the tank. 4Turn the selector knob to the boiler position ( ) and wait until the OK light glows. 5Turn the selector knob to the coffee position ( ) and allow half the solution to flow out. Turn the selector knob back to the off ( ) position to stop the flow. 6Leave the machine to stand for 15 minutes, then turn the knob to the coffee position ( ) and allow the tank to completely empty. 7 Thoroughly rinse the tank. Fill with fresh water and turn the selector knob to the coffee position ( ) and allow all the water to flush through. 8Turn the selector knob to the off ( ) position. Repairs caused by malfunctioning due to a build up of limescale in the product are not covered by the guarantee if the descaling process is not carried out regularly. service and customer care . If the cord is damaged it must, for safety reasons, be replaced by Kenwood or an authorised Kenwood repairer. If you need help with: . using your espresso machine . servicing or repairs Contact the shop where you bought your espresso. trouble shooting guide problem possible cause solution Espresso coffee doesn’t come out of the machine. . The coffee is damp and/or pressed too firmly into the filter. . The holes in the filter holder spouts are blocked. . The liquid coffee/boiler outlet is blocked. . The tank is incorrectly fitted and the valve at the bottom is not open. . The holes in the crema device are blocked. . Check that you are using ground coffee suitable for espresso makers. Press the coffee more lightly in the filter and change the grind if necessary. . Clean the holes in the spouts . Clean as indicated in the cleaning section. . Press the tank lightly so as to open the valve at the bottom . Dismantle the crema device and clean parts thoroughly. Se...
Questo manuale è adatto anche per i modelli :Macchine da caffè - ES430 (1.15 mb)