Log:
valutazioni - 5, GPA: 4.2 ( )

Istruzioni per l'uso Kenwood, Modello ESP100 series

Produttore : Kenwood
File Size : 284.16 kb
File Nome : a722c792-c5de-4574-b6fc-2d7447a6ecfc.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Fit the espresso pod filter into the pod filter holder (without a pod) and dispense one cup of water. . The coffee outlet nozzle can be raised or lowered to fit closer to the cup or mug on the cup stand. Simply pull down or push up . 11 When the OK indicator light stops flashing and glows continuously, turn the function lever to the upper coffee position () and a pre-determined quantity of coffee will dispense from the coffee outlet (see Fig. B page ii). 12 Once all the coffee has dispensed, the coffee maker will bleep. Return the function lever to the middle ( ) position. The OK light will flash for a couple of seconds until the pod filter holder can be removed and emptied (see Fig. C page ii). important Never attempt to remove the pod filter holder with force. Always wait a few seconds after making coffee as it will be held in place until it is safe to remove. 13 If you want to make further cups of coffee wait for the flashing OK indicator light to glow again continuously. Wait a few seconds then pull out the pod filter holder and fit a new coffee pod or change the pod filter if an alternative type of coffee is desired. Continue as above. Note: when making an espresso the coffee maker will make a pumping noise which will cease part way through the operation but will resume again before all the drink is dispensed. This ensures that the best coffee flavour is extracted. After each coffee is dispensed, excess water from the brewing process will be discharged into the drip tray. 2 to produce steam to froth milk after having brewed coffee 1Ensure that the pod filter holder with a pod holder is fitted to the coffee maker. 2Press the steam button and its light will flash (see Fig. D page ii). When the steam indicator light glows continuously the unit is ready to produce steam (see Fig. E page ii). 3 Place an empty jug under the steam/hot water nozzle and move the function lever to the lower steam position ( ) to remove excess water from the system. Return the function lever to the middle ( ) position and discard the water. 4 Part fill a jug with milk – the milk may increase up to three times in volume so select a suitably sized jug. . Fresh cold semi skimmed milk gives the best results. 5 Position the jug under the steam/hot water nozzle 6Place the nozzle into the milk and move the function lever to the lower steam position ( ). The milk will begin to increase in volume and appear frothy . To obtain a creamier froth, rotate the jug with slow movements from the bottom upwards. 7 Once the desired temperature and froth are obtained, stop the steam by returning the lever back to the middle ( ) position. . Never allow the milk to boil as this will spoil the flavour of the coffee. 8 Pour the frothed milk into the cups containing the espresso coffee to make a cappuccino. 9Switch off the steam button in order to make further cups of coffee. Note: After having used the steam function. The OK indicator light will flash quickly (once per 1.4 second) for a short period to indicate the high temperature (see Fig. F page ii) during which period of time the machine is not ready for brewing coffee. Wait until the OK indicator light glows continuously (see Fig. G page ii) otherwise the temperature will be too high and will burn the coffee. hint . After frothing milk, dispense hot water from the steam/hot water nozzle (see below) which will help clean the nozzle and help the boiler to cool down more quickly. to produce hot water for other drinks, eg tea, fruit drinks 1Ensure that the pod filter holder with a pod holder is fitted to the coffee maker. 2Press the power on button and its light will glow and the OK indicator light will flash. 3 When the OK indicator light stops flashing and glows continuously, place a cup under the steam/hot water nozzle and move the function lever to the lower steam position ( ). Hot water will dispense from the nozzle. 4 Switch off and unplug after use. . Never use teabags in the pod filter. setting the dispensing volume The coffee maker has been programmed to dispense a pre selected quantity of liquid which is 40ml for Espresso, 125ml for a single cafe crema and 250ml for a double cafe crema. These volumes can only be changed by carrying out the following procedure ensuring that the appropriate coffee pod and pod filter are fitted. 1 Place the required cups(s) under the coffee nozzle. 2Press and hold the Steam button for 5 seconds during brewing and the OK and steam indicator lights will flash simultaneously. When the coffee volume in the cup reaches the required level, release the button and the water volume will be stored in the memory. This can be re-programmed at any time following the above procedure. descaling When the power on indicator light starts flashing the machine needs to be descaled and it will continue to flash until the unit is descaled. 1With the machine switched off, place a jug under the steam/hot water nozzle. (This may need to be emptied during the descaling process.) 2 Fill th...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie