valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Before performing the following procedures, investigate all alarms and clear any trouble conditions. Refer to the Cisco ONS 15600 Troubleshooting Guide as necessary. This section lists the chapter procedures (NTPs). Turn to a procedure for applicable tasks (DLPs). 1. NTP-E157 Provision a Multirate PPM, page 11-2—Complete this procedure to provision a multirate pluggable port module (PPM), for the ASAP card. If a multirate PPM was preprovisioned, this procedure is unnecessary. 2. NTP-E151 Provision an Optical Line Rate, page 11-3—Complete this procedure to provision the optical line rate on a multirate PPM for the ASAP card. Single-rate PPMs do not need to be provisioned. 3. NTP-E150 Change the Optical Line Rate, page 11-4—As needed, complete this procedure to edit optical line rates for multirate PPMs on the ASAP card. 4. NTP-E149 Delete Pluggable Port Modules, page 11-5—As needed, complete this procedure to delete PPMs for the ASAP card. 5. NTP-E66 Modify Line and Status Thresholds for Optical Ports, page 11-6—As needed, complete this procedure to change line (drop) and threshold settings for all OC-N cards. 6. NTP-E105 Change an Optical Port to SDH, page 11-12—As needed, complete this procedure to change an optical port from SONET to SDH. 7. NTP-E125 Change Card Service State, page 11-13—As needed, complete this procedure to change card service state. Cisco ONS 15600 Procedure Guide, R5.0 February 2008 11-1 Chapter 11 Change Card Settings NTP-E157 Provision a Multirate PPM NTP-E157 Provision a Multirate PPM Purpose This procedure provisions a multirate pluggable port modules (PPMs) in CTC. Tools/Equipment None Prerequisite Procedures NTP-E147 Install the ASAP Card, page 2-5 DLP-E211 Install the ASAP 4PIO Modules, page 18-12, as needed DLP-E215 Install an SFP, page 18-14, as needed Required/As Needed Required Onsite/Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network. Step 2 Click the Alarms tab: a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on page 17-50 as necessary. b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide. c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition information. Step 3 In node view, double-click the ASAP card where you want to provision PPM settings. Step 4 Click the Provisioning > Pluggable Port Modules tabs. Step 5 In the Pluggable Port Modules pane, click Create. The Create PPM dialog box appears. Step 6 In the Create PPM dialog box, complete the following: • PPM—Click the slot number where the SFP is installed from the drop-down list. • PPM Type—Click the number of ports supported by your SFP from the drop-down list. If only one port is supported, PPM (1 port) is the only menu option. Step 7 Click OK. The newly created port appears on the Pluggable Port Modules pane. The row on the Pluggable Port Modules pane turns light blue and the Actual Equipment Type column lists the equipment name. Step 8 Verify that the PPM appears in the list on the Pluggable Port Modules pane. If it does not, repeat Steps 5 through 8. Step 9 Repeat the task to provision a second PPM. Step 10 Click OK. Step 11 Continue with the “NTP-E151 Provision an Optical Line Rate” procedure on page 11-3 to provision the line rate. Stop. You have completed this procedure. 11-2 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E151 Provision an Optical Line Rate NTP-E151 Provision an Optical Line Rate Purpose This procedure provisions the line rate on a multirate pluggable port module (PPM). Single-rate small-form factor pluggables (SFPs) or 4-port I/O modules (4PIOs) do not need line rate provisioning. Tools/Equipment None Prerequisite Procedures NTP-E148 Preprovision an SFP Slot, page 2-8 or NTP-E157 Provision a Multirate PPM, page 11-2 Required/As Needed Required Onsite/Remote Onsite or remote Security Level Provisioning or higher Step 1 Complete the “DLP-E26 Log into CTC” task on page 16-39 to log into an ONS 15600 on the network. Step 2 Click the Alarms tab: a. Verify that the alarm filter is not turned on. See the “DLP-E157 Disable Alarm Filtering” task on page 17-50 as necessary. b. Verify that no unexplained conditions appear on the network. If unexplained conditions appear, resolve them before continuing. Refer to the Cisco ONS 15600 SONET Troubleshooting Guide. c. Complete the “DLP-E76 Export CTC Data” task on page 16-98 to export alarm and condition information. Step 3 In node view, double-click the ASAP card where you want to provision the line rate. Step 4 Click the Provisioning > Pluggable Port Modules tabs. Step 5 In the Pluggable Ports pane, click Create. The Create Port dialog box appears. Step 6 In the Create Port dialog box, comple...