valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Protect it from dust, humidity, and heat. Step 2-1: Chassis Removal and Installation Step 1 Loosen the screw on the front chassis cover. Step 2 Push down the indentation located at the side of the back chassis. Step 3 Slide toward the top chassis cover. Step 4 Lift up to remove the top chassis cover. Step 5 Reverse Step 1, ,2, 3, 4 to replace the chassis cover Chapter 2 System Hardware Installation 1 2 3 4 12 GS-R227E-RH Rack Mount Server Step 2-2: CPU Installation Please make sure the CPU type and speed that are supported by the motherboard. Step 1 Raise the metal locking lever on the socket. Insert the CPU with the correct orientation. Step 2 The CPU only fits in one orientation. Step 3 Push the metal lever back into locked position. 1 2 3 13 Hardware Installation Process Step 2-3: Heat Sink Installation Step 1 Place the Heat Sink on the CPU. Before putting the heat sink on the CPU, please well remember to apply the thermal conductivity compound on the CPU. Step 2 Seat the heat sink in the retention modules with the four screws. Installation completed. 1 2 2 2 2 GS-R227E-RH Rack Mount Server Step 2-4: Memory Installation Step 1. Insert the DIMM memory module vertically into the DIMM slot, and push it down. Step 2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module. NOTE! DIMM must be populated in order starting from DIMM8 socket. For dual-channel operation, DIMMs must be installed in matched pairs. Step 3. Reverse the installation steps when you wish to remove the DIMM module. 1 2 2 14 15 GS-R227E-RH Rack Mount Server Step 2-5: PCI Expansion Card Installation GS-R227E-RH provides expansion riser slots for one PCI-E x8 slot; and one with PCI-E x8 slot (at x1 bandwidth). To install the peripheral, please go through the following steps. Step 1 Loosen the two riser bracket screws. (See illustrated below) Step 2 Loosen another four riser bracket screws. (See illustrated below) Step 3 Lift the riser bracket slightly, then pull it out from the server chassis. Align the expansion card with the guiding groove. Slide the expansion card into the slot until the card firmly seats. Step 4 Align the riser bracket to the system module. 1 1 2 2 2 2 3 16 Hardware Installation Process Step 2-6: Hard Disk Drive Installation Step 1 Press the release button. Step 2 Pull the blank out of the drive bay. Step 3 Slide hard disk into blank. Step 4 Secure it with screws. Step 5 Slide the blank into the bay until it locks into place. Connect cable and power. 1 2 3 4 4 17 Hardware Installation Process Step 2-7: FAN Duct Removal and Installation Step 1 Align the fan duct with the guiding groove. Push down the fan duct into system ntil the its firmly seats. 1 Guiding groove 18 GS-R227E-RH Rack Mount Server 3-1: Front View of GS-R227E-RH Chapter 3 Appearance of GS-R227E-RH .. .. .. .. .. .. .. .. DVD-COMBO Hot-Swap SATA HDDs USB connectors Front panel switch and LEDs System Appearance 3-2: Rear View of GS-R227E-RH .............. • • Power • Mouse connector • Keyboard connector • COM port • VGA port • USB connectors • RJ45 LAN ports • Low-profile riser slot • Full-Height riser slot 19 GS-R227E-RH Rack Mount Server 3-3: Switch and LED Indicators Introduction Buzzer Stop Reset RESETRESET BUZZER STOPBUZZER STOP ID Switch Power Button NameColor Condition Description PowerGreen On Power On Green Blink Sleep (S1) -Off Power Off (S4/S5) IDBlue On Unti selected for identification (Identification) -Off No identification 20 System Appearance 3-4: LAN LED Description NameColor Condition Description LANGreen O N LAN Link / no Access Link/ActivityGreen BLINK LAN Access -OFF Idle GbE LANYellow O N 1Gbps connection Speed Yellow BLINK Port identification with 1Gbps connection Green O N 100Mbps connection Green BLINK Port identification with 10 or 100Mbps connection -OFF 10Mbps connection 21 GS-R227E-RH Rack Mount Server 3-5: Connector Icon Description Suggest Icon Description Keyboard Mouse VGA COM LAN USB 22 Motherboard Layout Chapter 4 Motherboard Jumper Setting 4-1: GA-7BESV1-RH Motherboard Jumpper Setting PAS_DIS1 CLR_CMOS1 JP_REC1 23 GS-R227E-RH Rack Mount Server 1. CLR_CMOS1 ( (Clear CMOS jumper) You may clear the CMOS data to its default values by this jumper. Default value doesn’t include the “Shunter” to prevent from improper use this jumper. To clear CMOS, temporarily short 2-3 pin. 1 1-2 Close: Normal operation (Default setting) 1 2-3 Close: Clear CMOS 2. JP_REC1 (BIOS Revocery jumper) Open: Normal operation(Default setting) Close: Enable BIOS Recovery function. 3. PAS_DIS1 (Skip password jumper) 1 1-2 Close: Normal operation (Default setting) 2-3 Close: Skip supervisor password. 1 24 BIOS Setup Chapter 5 BIOS Setup BIOS (Basic Input and Output System) includes a CMOS SETUP utility which allows user to configure required settings or to activate certain system features. The CMOS SETUP saves the configuration in the CMOS SRAM of the motherboard. When the power is turned off, the battery on the motherboard supplies the...