Log:
valutazioni - 0, GPA: 0 ( )

Istruzioni per l'uso Dell, Modello Inspiron 560

Produttore : Dell
File Size : 821.89 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



da questo dispositivo ha anche altre istruzioni :

Facilità d'uso


5. If you are removing the card permanently, install a filler bracket in the empty card-slot opening. 6. Replace the card retention bracket (see Replacing the Card Retention Bracket). 7. Replace the computer cover (see Replacing the Computer Cover). 8. Connect your computer and devices to electrical outlets, and then turn them on. 9. Remove the card's driver from the operating system. 1 screw 2 guide clamps (2) 3 card retention bracket 4 guide notches (2) 5 filler bracket 6 alignment guide 7 alignment bar 1 PCI Express x16 card 2 PCI Express x16 card slot 3 securing tab 4 retention mechanism NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust and dirt out of your computer. 10. To complete the removal procedure, see Configuring Your Computer After Removing or Installing a PCI or PCI Express Card. Replacing PCI and PCI Express Cards 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the card retention bracket (see Removing the Card Retention Bracket). 4. If this is a new card installation, remove the filler bracket covering the card-slot opening. 5. Prepare the card for installation. See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your computer. 6. If you are installing the PCI Express card into the x16 card connector, position the card so the securing slot is aligned with the securing tab. 7. Place the card in the connector and press down firmly. Ensure that the card is fully seated in the slot. 8. Replace the card retention bracket (see Replacing the Card Retention Bracket). 9. Connect any cables that should be attached to the card. See the documentation for the card for information about the card's cable connections. 10. Replace the computer cover (see Replacing the Computer Cover). 11. Connect your computer and devices to electrical outlets, and then turn them on. 1 PCI Express x16 card 2 PCI Express x16 card slot 3 securing tab 4 securing slot 1 fully-seated card 2 not fully-seated card 3 alignment bar 4 alignment guide 5 bracket within slot 6 bracket caught outside of slot CAUTION: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment. 12. To complete the installation, see Configuring Your Computer After Removing or Installing a PCI or PCI Express Card. Configuring Your Computer After Removing or Installing a PCI or PCI Express Card Back to Contents Page NOTE: For information on location of external connectors, see the Setup Guide. For information on installing drivers and software for your card, see the documentation that shipped with the card. Installed Removed Sound Card 1. Enter system setup (see Entering System Setup). 2. Go to Onboard Audio Controller and then change the setting to Disabled. 3. Connect the external audio devices to the sound card's connectors. 1. Enter system setup (see Entering System Setup). 2. Go to Onboard Audio Controller and then change the setting to Enabled. 3. Connect the external audio devices to the computer's back panel connectors. Network Card 1. Enter system setup (see Entering System Setup). 2. Go to Onboard LAN Controller and then change the setting to Disabled. 3. Connect the network cable to the network card's connector. 1. Enter system setup (see Entering System Setup). 2. Go to Onboard LAN Controller and then change the setting to Enabled. 3. Connect the network cable to the integrated network connector. Back to Contents Page Battery Dell™ Inspiron™ 560/570 Service Manual Removing the Battery Replacing the Battery Removing the Battery 1. Record all the screens in System Setup (see System Setup) so that you can restore the correct settings after the new battery has been installed. 2. Follow the procedures in Before You Begin. 3. Remove the computer cover (see Removing the Computer Cover). 4. Locate the battery socket (see System Board Components). 5. Press the battery release lever to remove the battery. Replacing the Battery 1. Follow the procedures in Before You Begin. 2. Insert the new battery (CR2032) into the socket with the side labeled "+" facing up, and press the battery into place. 3. Replace the computer cover (see Replacing the Computer Cover). 4. Connect your computer and devices to electrical outlets, and then turn them on. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at WARNING: A new battery can explode if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions....


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie