valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
1 rear alignment notch 2 processor cover 3 center cover latch 4 processor 5 socket 6 tab 7 release lever 8 front alignment notch 9 processor pin-1 indicator 8. Pivot the socket release lever back toward the socket, and snap it into place to secure the processor. 9. Clean the thermal grease from the bottom of the heat sink. 10. Apply the new thermal grease to the top of the processor. 11. Replace the processor fan and heat sink assembly (see Replacing the Processor Fan and Heat Sink Assembly). 12. Replace the computer cover (see Replacing the Computer Cover). Back to Contents Page CAUTION: Ensure that you apply new thermal grease. New thermal grease is critical for ensuring adequate thermal bonding, which is a requirement for optimal processor operation. CAUTION: Ensure that the processor fan and heat sink assembly is correctly seated and secure. Back to Contents Page Drives Dell™ Studio XPS™ 8000 Service Manual Hard Drive Optical Drive Media Card Reader FlexDock Hard Drive Removing the Hard Drive 1. Follow the procedures in Before You Begin. 2. Remove the computer cover (see Removing the Computer Cover). 3. Disconnect the power and data cables from the hard drive. 4. Remove the graphics card bracket (see Removing the Graphics Card Bracket) 5. Remove the four screws that secure the hard drive to the drive panel. 6. To remove the secondary hard drive, remove the four screws that secure the secondary hard drive to the drive panel. WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at WARNING: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. WARNING: Do not operate your computer with any cover(s) (including computer covers, bezels, filler brackets, front-panel inserts, etc.) removed. CAUTION: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell™ is not covered by your warranty. NOTE: The 3.5-inch FlexDock is not interchangeable with the hard drive carrier. CAUTION: If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. NOTE: If you are not replacing the hard drive at this time, disconnect the other end of the data cable from the system board connector and set it aside. You can use the data cable to install a hard drive at a later time. CAUTION: Ensure that you do not scratch the hard drive's circuit board, while removing or replacing the hard drive. 7. Slide the hard drive out towards the back of the computer. 8. If removing the hard drive changes the drive configuration, ensure that you reflect these changes in the system setup (see System Setup). Replacing the Hard Drive 1. Follow the procedures in Before You Begin. 2. Check the documentation for the drive to verify that it is configured for your computer. 3. Slide the hard drive into the hard drive bay. 4. Align the screw holes in the hard drive with the screw holes in the drive panel. 5. Replace the four screws that secure the hard drive to the drive panel. 6. Connect the power and data cables to the hard drive (see System Board Components). 7. If you are replacing the primary hard drive, replace the graphics card bracket (see Replacing the Graphics Card Bracket). 8. Replace the computer cover (see Replacing the Computer Cover). 9. Connect your computer and devices to electrical outlets, and then turn them on. 10. See the documentation that came with the drive for instructions on installing any software required for drive operation. 11. Check the System Setup for drive configuration changes (see System Setup). Optical Drive Removing the Optical Drive 1. Follow the procedures in Before You Begin. 1 power cable 2 secondary hard drive 3 drive panel 4 screws (4) 5 primary hard drive 6 data cable 7 SATA connector 2. Remove the computer cover (see Removing the Computer Cover). 3. Remove the front bezel (see Removing the Front Bezel). 4. Disconnect the power and data cables from the optical drive. 5. Remove the two screws that secure the optical drive to the drive panel. 6. Push and slide the optical drive out through the front of the computer. 7. Set aside the optical drive in a secure location. Replacing the Optical Drive 1. Follow the procedures in Before You Begin. 2. Remove the screw from the old optical drive and insert it into the new optical drive. NOTE: If you are not replacing the optical drive at this time, disconnect the other end of the data cable from the system board connector and set it aside. You can use the data cable to install an optical drive at a later time. 1 screws (2) 2 optical drive 3 drive panel 4 SATA connector 5 data cable 6 power cable 3. Gently slide the optical drive into the optical drive bay through the front of the computer. 4. Align the scr...