valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
NOTICE: You must install both inserts in an empty 5.25-inch drive bay to maintain Federal Communications Commission (FCC) certification of the system. The inserts also help keep dust and dirt out of the system. 4. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. Diskette Drive Removing a Diskette Drive 1. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2. Remove the bezel. See "Removing the Bezel" in "Troubleshooting Your System." 3. Lay the system on its right side. 4. Remove the cover. See "Removing the Cover" in "Troubleshooting Your System." 5. Disconnect the power cable and the interface cable from the diskette drive. See Figure 7-2. 6. Remove the two screws that secure the diskette drive in the externally accessible drive bay. See Figure 7-2. 7. Slide the diskette drive forward out of the drive bay. Installing a Diskette Drive 1. Unpack the drive and prepare the drive for installation. For instructions, see the documentation that accompanied the drive. 2. Slide the diskette drive into the externally accessible drive bay. 3. Install the two screws that secure the diskette drive in the drive bay. See Figure 7-2. 4. Connect the power cable and the interface cable to the diskette drive. See Figure 7-2. 5. Install the cover. See "Replacing the Cover" in "Troubleshooting Your System." 6. Stand the system upright. 7. Install the bezel. See "Installing the Bezel" in "Troubleshooting Your System." 8. Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. Figure 7-2. Removing or Installing a Diskette Drive CAUTION: See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. CAUTION: See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. 5.25-Inch Drives An optical drive is standard in the first external drive bay. An additional IDE or SCSI tape backup device can be installed in the second external drive bay. These drives connect either to the system board or to an optional controller card. Installing a 5.25-Inch Drive 1. Unpack the drive (and controller card, if applicable), and prepare the drive for installation. For instructions, see the documentation that accompanied the drive. 2. Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 3. Remove the bezel. See "Removing the Bezel" in "Troubleshooting Your System." 4. Lay the system on its right side. 5. Remove the cover. See "Removing the Cover" in "Troubleshooting Your System." 6. Remove the cooling shroud. See "Removing the Cooling Shroud" in "Installing System Components." 7. Remove the front-panel inserts for the empty external drive bay. See "Removing the Front- Panel Drive Inserts." 8. Slide the drive into the external drive bay. 9. Install the screws that secure the drive in the drive bay. See Figure 7-3. Figure 7-3. Installing or Removing a 5.25-Inch Drive NOTE: Installing an additional optical drive in the second external drive bay is not supported. CAUTION: See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. NOTE: If you are installing a SCSI tape drive, you must install an Ultra 3 SCSI controller card. The optional SCSI RAID controller card does not support a SCSI tape drive. 10. If a controller card was supplied with the drive, install the controller card in expansion slot 3, 4, or 5. See "Installing an Expansion Card" in "Installing System Components." 11. Connect a power cable to the drive. See Figure 7-3. 12. Connect the interface cable to the drive and to the appropriate connector on the system board or controller card (if applicable). If you are installing an IDE device (such as an optical drive), connect the interface cable to the IDE device and the IDE connector on the system board. See Figure 7-4. If you are installing a SCSI device in the second drive bay (such as a tape backup device), connect the interface cable to the device and to channel A on the SCSI controller card. See Figure 7-4. See Figure A-3 to locate the system board connectors. Figure 7-4. Connecting a Tape Drive to a SCSI Controller Card 13. Ensure that all cables are firmly connected and arranged so that they will not catch on the computer cover or block airflow inside the system. 14. Install the cooling shroud. See "Installing the Cooling Shroud" in "Installing System Components." 15. Install the cover. See "Replacing the Cover" in "Troubleshooting Your System." 16. Stand the system upright. NOTE: See the documentation that is included with the controller card for more information. NOTE: A SCSI device attached to a SCSI controller ca...