valutazioni - 1, GPA: 5
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Getting Started With Your System 5 Turning On the System Press the power switch to the ON position. The power indicators should light. NOTE: Ensure that the storage enclosure is connected to the server and the mode switch set to split or unified mode before turning on the system. Installing the Optional Bezel Install the bezel (optional). Other Information You May Need WARNING: See the safety and regulatory information that shipped with your system. Warranty information may be included within this document or as a separate document. • The rack documentation included with your rack solution describes how to install your system into a rack. •The Hardware Owner’s Manual provides information about system features and describes how to troubleshoot the system and install or replace system components. This document is available online at support.dell.com/manuals. • Any media that ships with your system that provides documentation and tools for configuring and managing your system, including those pertaining to the operating system, system management software, system updates, and system components that you purchased with your system. NOTE: Always check for updates on support.dell.com/manuals and read the updates first because they often supersede information in other documents. NOM Information (Mexico Only) The following information is provided on the device described in this document in compliance with the requirements of the official Mexican standards (NOM): Importer: Model number: E03J Supply voltage: 100–240 V CA Frequency: 50/60 Hz Current consumption: 8.6 A Getting Started With Your System Technical Specifications Drives SAS hard drives Up to 12 3.5-inch SAS hot-swappable hard drives (3.0 Gbps and 6.0 Gbps) Enclosure Management Modules (EMMs) EMMs One or two hot-swappable modules with temperature sensors and an audio alarm Connectivity Configurations Support for either of the following configurations: • Unified mode for direct connectivity to 12 hard drives per enclosure. – Up to four daisy-chained storage enclosures for a total of 48 hard drives per controller port and 96 hard drives per controller. – Maximum configuration of two dual-port controllers per server for a total of 192 drives. – Redundant path connectivity provides redundant data paths to each hard drive. Redundant path configuration supports up to four daisy-chained storage enclosures for a total of 48 hard drives per controller and 92 hard drives per server. • Split mode with dual EMMs provides a direct connectivity to drives 0 through 5 and a separate direct connectivity to drives 6 to 11. Split mode configuration does not support redundant data paths. Getting Started With Your System Redundant Array of Independent Disks (RAID) Controller Host-based RAID support using PowerEdge™ RAID controller H800 Management RAID management using Dell OpenManage™ Server Administrator 6.2 or later. Back-Plane Board Connectors • 12 SAS hard-drive connectors • Two power supply/cooling fan module connectors • Two sets of EMM connectors • One control panel connector for front LEDs and enclosure mode switch Sensors Two temperature sensors Back-Panel Connectors SAS connectors (per EMM) • One SAS IN connector for connection to the host • One SAS OUT connector for expansion to an additional enclosure NOTE: SAS connectors are SFF-8086/SFF-8088 compliant. Serial connector (per EMM) One 6-pin UART mini-DIN connector NOTE: For engineering use only LED Indicators Front panel • One two-color LED indicator for system status • Two single-color LED indicators for power and split mode Hard-drive carrier One single-color activity LED One two-color LED status indicator per drive Getting Started With Your System LED Indicators (continued) EMM Three two-color LED status indicators, one each for the two EMM SAS ports and one for the EMM status Power supply/cooling fan Three LED status indicators for power supply status, power supply/fan fault, and AC status Switch System identification button Located on the front control panel. This button is used to locate a system within a rack. Mode switch Located on the front control panel. Used to switch the system between unified and split mode operation. Power Supplies AC power supply (per power supply) Wattage 600 W Voltage 100–240 VAC (8.6 A–4.3 A) Heat dissipation 188 W Maximum inrush current Under typical line conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply for 10 ms or less. Available Hard Drive Power (Per Slot) Supported hard drive power Up to 1.16 A at +5 V consumption (continuous) Up to 1.6 A at +12 V EMM Power (Per Slot) Maximum power consumed by EMM 11 W at +12 V Maximum available power 100 W at +12 V Maximum available power 1 W at +5 V standby Getting Started With Your System Physical Height Width Depth Weight (maximum configuration) Weight (empty) 8.68 cm (3.41 inches) 44.63 cm (17.57 inches) 60.20 cm (23.70 inches) 28.39 kg (62.6 lb) 8.84 kg (19.5 lb) Environmenta...