valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 154. Installing or replacing a hot-swap hard disk drive Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 67. This topic provides instructions on how to install or replace a hot-swap hard disk drive. For a list of the ThinkServer hard disk drive options, go to: You can install or replace a hot-swap hard disk drive without turning off the server, which helps you avoid significant interruption to the operation of the system. The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. The number of the installed hard disk drives in your server varies depending on the server model. The vacant bays are occupied by dummy hard-disk-drive trays. When you install a hot-swap hard disk drive, save the removed dummy hard-disk-drive tray from the drive bay in the event that you later remove the hot-swap hard disk drive and need the dummy tray to cover the place. Attention: An unoccupied drive bay without any other protection might impact the EMI integrity and cooling of the server, which might result in overheating or component damage. To maintain the EMI integrity and Chapter 6. Installing, removing, or replacing hardware 115 cooling of the server, install a new hot-swap hard disk drive as soon as you remove the failing one or the dummy tray. Before you begin, review the following hard disk drive installation rules: • Follow the order of the hard-disk-drive bays when installing a hard disk drive. See “Server components” on page 25 to locate the hard-disk-drive bays in your server. • For RAID configuration, the hard disk drives must be the same type with the same capacity if they are within a single RAID array. For more information, see “Configuring RAID” on page 62. • For hard disk drives with different capacities, install the hard disk drive by following the order of the hard-disk-drive bays as well as the order from the lowest capacity to the highest capacity. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the model, your server might come with 3.5-inch hot-swap hard disk drives or 2.5-inch hot-swap hard disk drives. The illustrations in this topic are based on server models with 3.5-inch hot-swap hard disk drives. For other models, the replacement procedure is similar. • Depending on the model, your server might look slightly different from the illustrations in this topic. • Use any documentation that comes with the hot-swap hard disk drive and follow those instructions in addition to the instructions in this topic. To install or replace a hot-swap hard disk drive, do the following: 1. Locate the appropriate hard-disk-drive bay. See “Server components” on page 25. 2. Press the release button 1 to open the handle of the hot-swap hard disk drive or the dummy tray. IDMemCPUPSU Figure 79. Opening the handle of the hot-swap hard disk drive 116 ThinkServer RD540 User Guide and Hardware Maintenance Manual Figure 80. Opening the handle of the dummy hot-swap hard-disk-drive tray 3. Pull the handle and carefully slide the hot-swap hard disk drive or the dummy tray out of the front of the chassis. IDMemCPUPSU Figure 81. Removing the hot-swap hard disk drive Chapter 6. Installing, removing, or replacing hardware 117 Figure 82. Removing the dummy hot-swap hard-disk-drive tray 4. Touch the static-protective package that contains the new hot-swap hard disk drive to any unpainted surface on the outside of the server. Then, take the new hot-swap hard disk drive out of the package. Note: Do not touch the circuit board on the hard disk drive. 118 ThinkServer RD540 User Guide and Hardware Maintenance Manual 5. Slide the new hot-swap hard disk drive into the drive bay from the front until it snaps into position and then completely close the handle. IDMemCPUPSU Figure 83. Installing the hot-swap hard disk drive 6. Check the hot-swap hard-disk-drive status LEDs to ensure that the hard disk drive is operating correctly. You might have to restart the server for the newly installed hard disk drive to be recognized. See “Hot-swap hard-disk-drive status LEDs” on page 30. If the hard disk drive is faulty, you need to reinstall or replace it until it is operating correctly. 7. Do one of the following: • If you are installing a hot-swap hard disk drive, save the removed dummy hard-disk-drive tray in the event that you later remove the hot-swap hard disk drive and need a dummy tray to cover the drive bay. • If you are replacing a hot-swap hard disk drive and are instructed to return the old hot-swap hard disk drive, follow all packaging instructions and use any packaging materials that are supplied to y...
Questo manuale è adatto anche per i modelli :Computer - ThinkServer RD540 (70AS) (13.08 mb)
Computer - ThinkServer RD540 (70AT) (13.08 mb)
Computer - ThinkServer RD540 (70AU) (13.08 mb)