valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
1. Pull the quick release lever towards the rear of the case and release Looking from the rear of the case you can see some metal grills (external) drive bays. Carefully put a screwdriver through the metal grill and gently push the plastic drive bay cover until it comes off. Carefully use your hands to twist the metal plate back and forth until it breaks off. Note: Don't take off the covers and plates for the drive bays that you are not using now. Be careful of the newly exposed metal where the grills were attached, as these areas are likely to be sharp. 2. Install your floppy drive into the top drive bay. 3. Mount your other 3.5" device into the drive cage. Note: If you want to have a cooling fan in the drive cage, you should install the fan before installing the drives. 4. Slide and lock the drive cage back into the case. 5. Release the second cage. Note: Inside the cage you will find a fan bracket. This is for one of the optional 80mm cooling fans. If you want to install the optional fan you should do it now. For fan installation please see the Fan Installation section of this manual. 6. Mount your other 3.5" devices into the drive cage. 7. Slide and lock the drive cage back into the case. 8. Find a small 4-pin white connector on the power supply and connect it to the male 4-pin connector on the floppy drive. 9. Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the other devices. 5.25" Device Installation 1. Take off the plastic drive bay covers and metal plates as described above. 2. Take two of the Drive Rails and mount them to the sides of the 5.25" device. Make sure the metal portion is angled away from the device and facing forward. 3. Slide the device into the drive bay until you hear a click. 4. Mount the other devices accordingly. Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the devices. 3 Data Cable After you have you need to cables between the The data cables are case; we include this information 1. For hard drives and CD-For floppy drives, use the 34-pin IDE ribbon These should come with have a red strip on one side When you connect a ribbon cable to a device, make sure that connector. 2. The end that attachs to devices should This will enable you to connect another device if 3. Connect the far end of the cable to your motherboard or IDE 2, or the FLOPPY port. Fan Installation The case comes preinstalled with two 80mm cooling The fans are installed so that the air is blowing out of the case. Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the fans. Optional Cooling fans: The case has two optional 80mm cooling fans that can be installed in the front of the case. One of the optional fans is located inside the 3.5" drive cage. You should install the fan first before you mount your drives into the cage. Install the fans so that the air is blowing into the case from the front. 1. Drop the fan into the fan bracket and push it in until it snaps in. 2. Connect a large 4-pin white connector from the power supply to the male 4-pin connector on each of the fans. Washable Air Filter Maintainence From time to time it will be necessary to wash the installed air filter. Not washing the air filter will result in higher system temperatures and possible stability problems. We recommend checking the air filter at least once a month initially. The frequency will change depending on system usage (users whose systems run 24/7 will likely have to check/wash more often than those who don't use their systems every day) and on environmental conditions. 4 Antec Quality Warranty Antec, Inc., warrants this or faulty components under I. Warranty Length Parts and labor are warranted for three Replacement products will be warranted for the remainder is longer. II. Who Is Protected This warranty is enforceable only by the original III. What Is And Is Not Covered It is important to note that our warranty is not an unconditional length of the warranty. Antec Products are made from the finest materials available under our exacting manufacturing standards. But, like any other product, they are not indestructible. Therefore, our warranty does not cover product damage that may abuse or mishandling of the products, nor does it cover incidental or Also, as with any product, it should be expected that component parts, moving etc. will show wear with use over time, and eventually may need to be refurbished replaced. This type of normal wear and tear is naturally not covered by our warranty, but we will always be happy to provide you with prompt, high-quality repair service at cost. All Antec products are covered by this 3 year warranty except keyboards, monitors and any product purchased before the inception of this warranty program which is November 1, 2000. The following are not covered by the warranty: 1. Any product on which the serial number has been defaced, modified, or removed...
Questo manuale è adatto anche per i modelli :Computer - PERFORMANCE II SERIES SX1000BII (136.28 kb)