valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
"Opening the rack door" on page 40 2. "Locate the faulty server" on page 37 3. "Shutting down the server" on page 41 4. "Sliding the server out of the rack" on page 42 5. "Removing the rear cover" on page 46 6. "Locate the faulty component by PRIMERGY diagnostics indicators" on page 39 8.10.3 Removing the PCI Riser ...... Figure 94: Removing the PCI Riser 164 Maintenance Manual RX900 S1 Expansion cards and BBU E Press the green button (1). E Lift the handle (2) to disconnect the PCI Riser (PCIR) from the baseboard. E Pull the PCIR up and out by using the handle (3). 8.10.4 Removing the Modular RAID controller ............ Figure 95: Removing the Modular RAID controller from the slot E Remove the slot lock by pulling the green handle upward (1), pushing the plastic part down (2), and lifting the slot lock (3). E Carefully pull the Modular RAID controller out of the lot (4). E Disconnect the SAS cables from the Modular RAID controller ports. RX900 S1 Maintenance Manual Expansion cards and BBU 8.10.5 Inserting the Modular RAID controller ..A ..B Figure 96: Connecting the SAS cables E Connect the SAS cables to the Modular RAID controller ports as follows: – MLC1 port (A): HDD/SSD modules #0, #1, #2, #3 – MLC2 port (B): HDD/SSD modules #4, #5, #6, #7 166 Maintenance Manual RX900 S1 Expansion cards and BBU ...... Figure 97: Inserting the Modular RAID controller E Carefully insert the Modular RAID controller in its slot (1). E Insert the slot lock (2) and relock the slot (3). RX900 S1 Maintenance Manual Expansion cards and BBU 8.10.6 Installing the PCI Riser .... Figure 98: Installing the PCI Riser E Carefully insert the PCIR in the slot (1). E Lock the PCIR by pushing down the handle (2). 8.10.7 Completing the task E Perform the following procedures to complete the task: 1. "Installing the rear cover" on page 48 2. "Mounting the server in the rack" on page 49 3. "Bringing the server back to operation" on page 51 4. "Closing the rack door" on page 51 168 Maintenance Manual RX900 S1 Expansion cards and BBU 8.11 Installing a Battery Backup Unit (BBU) Authorized personnel Authorized specialist personnel can carry out replacement tasks for integral server components. Ask you local Fujitsu service center for more detailed information. V CAUTION! Procedures indicated as "Authorized personnel only“ must be done by Fujitsu service personnel or technicians trained by Fujitsu for doing these tasks. Please note that unauthorized interference with the system will void the warranty and exempt the manufacturer from all liability. V CAUTION! . Do not connect the cable using excessive force, the connector is weak. . Follow the safety instructions in the "Safety instructions" on page 31. The Battery Backup Unit (BBU) backs up the memory contents of the SAS RAID controller in the event of a power failure. A maximum of two BBUs can be installed for each system. I The RX900 S1 server can be equipped with one Modular RAID controller and two SAS RAID controllers but only for two of these RAID controllers a BBU can be installed. 8.11.1 Required tools . Starting and completing the task: – key for the rack doors (if applicable) – Phillips Ph2 screw driver . Installing the BBU: tool-less RX900 S1 Maintenance Manual Expansion cards and BBU 8.11.2 Starting the task E Perform the following procedures: 1. "Opening the rack door" on page 40 2. "Shutting down the server" on page 41 3. "Sliding the server out of the rack" on page 42 4. "Removing the rear cover" on page 46 8.11.3 Connecting the BBU cable to the BBU Figure 99: Connecting the BBU cable E Connect the BBU cable to the battery. I The cable can only be installed in one direction. Make sure that the markings on the connector are aligned with the corresponding marking on the socket. 170 Maintenance Manual RX900 S1 Expansion cards and BBU 8.11.4 Installing the BBU in the BBU holder Figure 100: Removing the BBU holder E Remove the BBU holder from the chassis by lifting it with the green handle. ..................A ..B Figure 101: Installing the BBU in the BBU holder RX900 S1 Maintenance Manual Expansion cards and BBU E Select the battery holder as follows: – A: Insert the BBU for the Modular RAID controller in PCIe slot #8. – B: Inset the BBU for one of the SAS RAID controllers. E Insert the battery at a slight angle behind the clips (1). E Carefully press the battery into the holder until it engages under the two locking hooks (2). E Route the BBU cable through the cable clamps (3). E Install the BBU holder with the BBU in the chassis. 172 Maintenance Manual RX900 S1 Expansion cards and BBU 8.11.5 Connecting the BBU to the Modular RAID controller ...... Figure 102: Connecting the BBU to the Modular RAID controller RX900 S1 Maintenance Manual Expansion cards and BBU E Route the BBU cable through the cable clamps (1). I Avoid cable loops in the PCIe slot area. The BBU cable must be fixed in the cable clamps (1). E Connect the BBU cable to the Modular RAID controller (2). I The cable can only...
Questo manuale è adatto anche per i modelli :Computer - PRIMERGY RX900 S1 (7.89 mb)