valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Replace All Covers and
System
Connect All Cables
10
Board
1
3
1
1. Lower the system board: If the system board is in the raised
Thumbscrews
position, hold the handles of the retaining latches vertical, and push the
Side
system board down to seat it firmly in its slot. Then, lower the retaining
Cover
Top
Cover
latches simultaneously to secure the board.
2. Replace all covers:
2
a.If a side cover was removed, insert its lower channel onto the lip at
the bottom of the chassis. Press the top of the side cover against the
chassis, so that it snaps it into place.
b.To replace the top cover, align both corners of its rear edge against
the similar sheet metal on the rear of the HP NetServer. Lower the
front of the top cover and pull it forward slightly to catch on the rear
of the chassis and to clear the front edge of the chassis. Tighten
both thumbscrews.
c. Align the front bezel against the front of the HP NetServer, and
press it firmly into place. Lock the front bezel with the key provided.
3. Connect the power cord and all other cables.
Front
CAUTION Replace ALL covers before operating the
Bezel
HP NetServer, even for a short time. Otherwise,
overheating can damage processors, boards, and
mass storage devices.
Verify Installed Accessories
NOTE
SCSI devices connected to a disk array controller board
(Optional)
11
(DAC) cannot be displayed at boot time. An ISA non-Plug-
and-Play board cannot be displayed at boot time.
The boot screen lists the hardware that the system detected, such as
If you wish, you may now verify accessories you have installed. Turn on
CPU, DIMMs, and PCI and ISA boards. If the system fails to restart, follow
the HP NetServer and monitor, and view the the boot screen.
the instructions on the screen.
Configure the HP NetServer
12
3. Select the NOS: Select the NOS you will install, and the version if
necessary. Installation of the optional IntranetWare NOS, which is in the
HP NetServer Software Option Package, requires the key obtained in
Section 5: "Prepare for Installation."
4.
Select the NOS installation mode:
1. Turn on the HP NetServer and monitor,
If you
and insert the HP
select certain versions of Novell NetWare / IntranetWare or Microsoft
Navigator CD-ROM into the drive. Turn the power off, wait 10 seconds,
Windows NT Server, you will be asked, "Would you like to use HP's
and turn the power on again. If the system fails to restart, follow the
automated mode of NOS installation?"
instructions on the screen.
If you want to use automated NOS installation,
select "Yes." Choose automated NOS installation mode for first-time
installation of Novell NetWare / IntranetWare or Microsoft Windows NT
NOTE
If you have installed an ISA non-Plug-and-Play accessory
Server on a factory-configured HP NetServer LC II.
board, you must reserve system resources for it by using
the Setup utility. Start the Setup utility by pressing the F2
Perform a manual NOS installation if you are
function key when "Press
installing a NOS other than Novell NetWare / IntranetWare or Microsoft
on the boot screen.
Windows NT Server, or if you replaced HP components. (For example,
if you replaced an HP network interface controller board with a third-
When the Setup utility starts, select "Configuration," and
party board, install the NOS manually.)
then select "ISA non-Plug-and-Play Devices." Use the
arrow keys to highlight a selection, press ENTER to display
5.
Configure Remote Management: If you
its options, and use the +/- keys to change values. When
plan to manage the HP NetServer LC II remotely, refer to the HP
done, exit saving changes. For more about reserving
NetServer LC II Remote Administrator Guide. Select "Configure
system resources, refer to Information Assistant and to
Remote Management" on the Configure Remote Management screen
"Configuring ISA Non-Plug-and-Play Board" in Chapter 4,
to start the utility that configures Integrated Remote Assistant.
"Accessories," in the HP NetServer LC II Series User
6.
Configure Disk Array: If you have a disk
Guide.
array, refer to the HP NetRAID Series Installation and Configuration
.
Guide Select "Execute" on the Configure Disk Array screen to start the
(If the system hangs before the Setup utility starts, remove
utility that configures the disk array.
the ISA non-Plug-and Play board, run the Setup utility to
reserve system resources for it, and reinstall the board.)
7.
Install the NOS: If you selected the HP
automated NOS installation process, you will be guided through the
process by a series of HP display screens.
2. Run Configuration Assistant and Installation Assistant:
To install the NOS manually:
Go to the HP Navigator Main Menu. If you want to change the
language, select "Set Preferences" and the language. Select
! On the Create Driver Diskette(s) screen, select "Create Drivers
"Configuration and Installation Assistant." Select "Express" from the
Diskette(s)."
next screen to begin the "Express" mode of configuration.
! On the Show NOS Installation Instructions screen, select "Save to
Disk." Then print out the Network Operating System Installation
"Custom" configuration mode and "Replication" configuration mode are
Instructions from the disk. Read these instructions before starting to
also available. Refer to the HP NetServer LC II User Guide for details.
install the NOS.
!
NOTE
To use the Console Redirection feature of Integrated
Follow the instructions on the screen and the Network Operating
Remote Assistant to run server management utilities
System Installation Instructions to perform the manual NOS
remotely, you must create the utility partition. "Express"
installation.
configuration mode creates it automatically. If you use
8. HP NetServer management: Refer to the HP NetServer
"Custom" configuration mode, create the partition by
Management Reference Guide, and install HP TopTools.
selecting "Install/Update Utility Partition" from the Custom
Configuration menu within Configuration Assistant.
Install in Rack (Optional)
13
To install the HP NetServer in a rack assembly, refer to the following:
• Rack installation kit instructions
• HP NetServer Rack Assembly and Cabling Reference Guide
After completing the installation in the rack assembly, return to the HP
NetServer Rack Installation Road Map.