valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Before You Begin
Physical Installation
labeled “Console”) to the serial port of any terminal.
Type an appropriate name in the Name field of the
This Quick Start Guide guides you from initial physical
WARNING: Do not remove the SA7150’s cover. There are
Connection Description window (e.g., “Config”), and
then click the OK button. The Phone Number panel
installation of the HP e-Commerce/XML Server Accelerator
no user-servicable parts inside.
appears.
SA7150 to an active command line prompt (i.e., the “test”
Rack Installation
2.
In the Connect Using… field specify “COM1” (or the
configuration). To proceed from the test configuration to
serial port through which the PC is connected to the
production, refer to the HP e-Commerce/XML Server
Rack mounting requires the use of the mounting brackets
SA7150 if different from COM1).
Accelerator SA7150 User Guide.
and all four of the included mounting screws.
3.
Click the OK button. The COM1 Properties panel
Parts Checklist
1.
Attach a mounting bracket to each side of the SA7150,
appears. Set the values displayed here to 9600, 8, none,
using two of the provided screws for each bracket. Use
1, and none.
Ensure that the items listed below are included in the box
the holes near the front of the SA7150’s sides. The
4.
Click the OK button.
with your SA7150:
brackets have both round and oval holes; the flange with
round holes attaches to the SA7150; the one with oval
Using HyperTerminal*
•
HP e-Commerce/XML Server Accelerator SA7150
holes attaches to the rack.
•
HP e-Commerce/XML Server Accelerator SA7150 User
2.
Position the SA7150 in the desired space of your 19”
If you’re using HyperTerminal* you must make the following
Guide
rack and attach the front flange of each mounting bracket
configuration change:
to the rack with two screws each. (Rack-mounting
1.
In the File menu, click Properties.
•
HP e-Commerce/XML Server Accelerator SA7150
screws are not provided.)
Release Notes
2.
Click the Settings tab.
Free-Standing Installation
3.
Click the ASCII Setup button.
•
AC power cord
4.
Change the values of Line and Character delay from 0 to
•
Serial cable
1.
Attach the provided self-adhesive rubber feet to the
at least 1 millisecond.
SA7150’s bottom.
•
Rack and rail mounting brackets and mounting screws
5.
Click OK to exit ASCII setup.
2.
Place the SA7150 on a flat surface and make sure that
Pre-Installation Requirements
there is adequate airflow space around the unit (allow at
6.
Click OK to exit Connection Properties.
least one inch of air space on all sides).
Accessing the Command Prompt
•
IP address for SA7150 (Required if you intend to use the
SA7150’s remote management capabilities. Please see
Network Connections
After the SA7150 boots up, the password prompt appears.
Chapter 6 of the User Guide for details.)
1.
Use the table near the beginning of this guide to
NOTE: The password is not echoed on the command line.
•
IP addresses and port numbers of servers
select the appropriate cables.
1.
Type admin at the password prompt and press
•
Keys/certificates (Required if you anticipate supporting
NOTE: Never connect both ports to the same network
<Enter> to access the prompt:
secure transactions. Please see Chapter 3 of the User
segment (e.g., to the same hub, switch, or router). Doing so
Password: admin (password is not echoed at prompt)
Guide.)
creates a feedback loop that adversely affects network
Current date: 2000 11/01 05:01
bandwidth.
•
Network cables (Category 5 UTP or better), as indicated
HP SA7150>
2.
Apply power to the device by connecting the provided
by the following table:
power cable to the back of the unit. (There is no power
You are now ready for operations at the Command Line
switch.) Under normal circumstances, the SA7150
Interface (CLI) of the SA7150. A typical way to begin would
To SA7150’s
To SA7150’s
requires approximately 30 seconds to boot. When the
be as follows:
network
server
boot is complete, the unit’s Power LED is steadily
1.
Optionally, use the password command to change
connector
connector
illuminated. (If the Power LED is not steadily illuminated,
your password from admin to another password.
please see Chapter 9, “Troubleshooting,” in the User
Workstation or
Crossover cable
Straight-through
Guide.)
HP SA7150> password
Server
cable
3.
If the Inline LED is neither steadily illuminated or blinking,
2.
Use set date to correct the date/time, if necessary.
press the Bypass switch to enable Inline mode.
The date and time affect the validity of the certificate.
Switch or Hub
Straight-through
Crossover cable
4.
Now both the Network and Server LEDs should be
HP SA7150> set date
cable
steadily illuminated. If not, please see Chapter 9,
“Troubleshooting,” in the User Guide.
3.
Use the help command to list available commands (or
Router
Crossover cable
Not recommended
refer to the Command Reference in Chapter 5 of the
NOTE: Configuration of multiple SA7150s requires special
User Guide).
care in cabling. Please see Chapter 2 in the User Guide for
SA7150’s
N/A
Straight-through
details.
HP SA7150> help
network
cable
connector *
Console Connection
4.
Configure XML servers and patterns as appropriate for
your business needs. (See Chapter 3 of the User Guide
for details.)
SA7150’s server
Straight-through
N/A
Run a terminal emulator on your PC. (The steps below
connector *
cable
5.
If your operational model includes SSL traffic, configure
assume the use of HyperTerminal*. Other terminals will
the appropriate keys and certificates. (See Chapter 3 of
require different procedures.)
* Applies to multiple, cascaded devices only.
the User Guide for details.)
1.
Use the serial cable provided with the SA7150 to
connect the device’s serial port (the serial port