valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
NOTICE This symbol indicates special notes. Features Symbols used in this Manual Air Intake Vents Air Outlet Vents Connecting Wires Piping Base Plate Drain Hose Front Panel Air Inlet Signal Receptor Air Filter Indoor Outdoor This appliance should be installed in accordance with national wiring regulations. This guide acts as a guide to help to explain product features. Electrical Safety Electrical Safety • This appliance must be properly grounded. To minimize the risk of electric shock, you must alway plug into a grounded oulet. • Do not cut or remove the grounding prong from the power plug. • Attaching the adapter ground terminal to the wall receptacle cover screw does not ground the appliance unless the cover screw is metal and not insulated, and the wall receptacle is grounded through the house wiring. • If you have any doubt whether the air conditioner is properly grounded, have the wall receptacle and circuit checked by a qualified electrician. Temporary Use of an Adapter We strongly discourage the use of an adapter due to potential safety hazards. For temporary connections, use only a UL-listed adapter, available from most local hardware stores. Ensure that the large slot in the adapter is aligned with the large slot in the receptacle for a proper polarity connection. To disconnect the power cord from the adapter, use one hand on each to avoid damaging the ground terminal. Avoid frequently unplugging the power cord as this can lead to eventual ground terminal damage. • Never use the appliance with a broken adapter. Temporary Use of an Extension Cord We strongly discourage the use of an extension cord due to potential safety hazards. For temporary situations, use only CSA certified and UL listed 3-wire grounded extension cords, rated 15 A, 125 V. ENGLISH Owner's Manual 11 12 Room Air Conditioner Operation indicating lamps Operating Instructions How to insert the Batteries Storage and Tips for using the Remote Controller 1. Remove the battery cover by pulling it according to the arrow direction. 2. Insert new batteries making sure that the (+) and (-) of battery are installed correctly. 3. Reattach the cover by sliding it back into position. Use 2 AAA(1.5volt) batteries. Do not use rechargeable batteries. NOTICE • The remote controller may be stored by mounting it on a wall. • To operate the room air conditioner, aim the remote controller at the signal receptor. Operating Instructions Signal Receptor Receives the signals from the remote control.(Signal receiving sound: two short beeps or one long beep.) *Hot Start operation: Stops the indoor fan in Heating Operation to prevent cold air from blowing out from unit. Operation Indication Lamps On/Off : Lights up during the system operation. Sleep Mode : Lights up during Sleep Mode Auto operation. (Without plasma model only) Timer : Lights up during Timer operation. Defrost Mode : Lights up during Defrost Mode or Start operation (Heat pump model only) : Lights up during outdoor unit operation. (Cooling model only) : Indicates the setting temperature Plasma : Lights up during plasma operation (Plasma model only) OUT DOOR OUTDOOR UNIT OPERATION Display Lights up during Sleep Mode Auto operation. (Plasma model only) 88 PLASMA *Hot Operating Instructions Remote Control Operations The controls will look like the following. Controls Signal transmitter ON OFF CANCEL AUTO CLEAN SET 1 3 5 4 9 10 12 14 16 7 2 8 13 15 11 6 Cooling Operation Auto Operation or Auto Changeover Healthy Dehumidification Operation Flip-up door (opened) Heating Operation • Cooling Model( ), Heat Pump Model( ) 17 Operation Mode 1. START/STOP BUTTON Operation starts when this button is pressed and stops when the button is pressed again. 2. OPERATION MODE SELECTION BUTTON Used to select the operation mode. 3. ROOM TEMPERATURE SETTING BUTTONS Used to select the room temperature. 4. INDOOR FAN SPEED SELECTOR Used to select fan speed in four steps low, medium, high and CHAOS. 5. JET COOL Used to start or stop the speed cooling.(speed cooling operates super high fan speed in cooling mode.) 6. CHAOS SWING BUTTON Used to stop or start louver movement and set the desired up/down airflow direction. 7. ON/OFF TIMER BUTTONS Used to set the time of starting and stopping operation. (See page 22) 8. TIME SETTING BUTTONS Used to adjust the time. (See page 22) 9. TIMER SET/CANCEL BUTTON Used to set the timer when the desired time is obtained and to cancel the Timer operation. (See page 22) 10. SLEEP MODE AUTO BUTTON Used to set Sleep Mode Auto operation. (See page 22) 11. AIR CIRCULATION BUTTON Used to circulate the room air without cooling or heating. (See page 23) 12. ROOM TEMPERATURE CHECKING BUTTON Used to check the room temperature. 13. NEO PLASMA(OPTIONAL) Used to start or stop the plasma-purification function. (See page 20) 14. HORIZONTAL AIRFLOW DIRECTION CONTROL BUTTON (OPTIONAL) Used to set the desired horizontal airflow direction. 15. RESET BUTTON Used prior to resetting time. 16. 2nd F Button Used ...
Questo manuale è adatto anche per i modelli :Condizionatori - LG-BKE7650 D, LG-BKE7700 D (2.97 mb)