valutazioni - , GPA: ( )

Istruzioni per l'uso Danby, Modello DAC5210M

Produttore : Danby
File Size : 443.12 kb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Inadequate support on control side of the unit can result in personal injury and damage to your unit and property. Therefore, it is recommended that you have someone assist you during the installation of this unit. 3/4” screws (9) 3/8” screws (4) Safety Lock (1) Adhesive Foam Seal (1) Frame Lock (2) Regular FoamSeal (1) Side Curtain RH (1) Side Curtain LH (1) Fig. 1 INSTALLATION HARDWARE L shaped mountingbracket (1) 3 INSTALLATION INSTRUCTIONS (cont’d) LOCATION A) This room air conditioner is designed to fiteasily into a single or double hung window. However, since window designs vary, it may be necessary to make some modifications for safe, proper installation. B) Make sure window and frame are structurally sound and free from dry and rotted wood. C) For maximum efficiency, install the air conditioner on a side of the house or building which favours moreshade than sunlight. If the unit is in direct sunlight, itis advisable to provide an awning over the unit. D) Provide sufficient clearance around the cabinet to allow for ample air circulation through the unit (SeeFig. 2). The rear of the unit should be outdoors and not in a garage nor inside a building. Keep unit as faraway as possible from obstacles/obstructions and atleast 30” above the floor or ground. Curtains and other objects within a room should be prevented fromblocking the air flow. E) Be certain the proper electrical outlet is withinreach of the installation. Use only a single outletcircuit rated at 15 amps. All wiring should be in accordance with local and national electrical codes. F) DO NOT install unit where leakage of combustible gas is suspected. Your air conditionermay fail to operate in air containing oils (includingmachine oils), sulfide gas, near hot springs, etc. NOTE: Your unit is designed to evaporate condensationunder normal conditions. However, under extreme humidity conditions, excess condensation may causebasepan to overflow to the outside. The unit should beinstalled where condensation run-off cannot drip on pedestrains or neighboring properties. Awning Fence, wall, or other obstacleGround Side Obstruction 20” Min 30” Min 20” Min 12” Min Fig. 2 1) Assembly of the Upper Channel to Cabinet. • “L” Shaped Top Channel: Install the “L” shaped channel to thetop of the cabinet as shown in Fig. 3, using four (4) 3/8” screws. 2) Assembly of the Side Curtains to Cabinet. • Extend the shutter from the shutter frame and slide it into the shutter tabs on the side channel of the air conditioner, as shown in Fig. 4. • Slide the shutters into the top (“L” Shaped) and bottom (“U” Shaped) channels. The shutters are identified (on frame) as leftand right. 3) Completing the Installation • Cut the foam (non adhesive) sealing strip to fit the area of thewindow sill that the air conditioner will rest on. 4 3/8” screws “L” shapedmounting bracket “U” shaped Channel(Factory Installed)Fig. 3 Slide down into tabs Shutter tabs Shutter Shutter frame Fig. 4 INSTALLATION INSTRUCTIONS (cont’d) 3) Completing the Installation (cont’d) • Carefully place the air conditioner into the window with the “L” shaped mounting bracket (on top) positioned in front of the upperwindow sash. The bottom of the cabinet should be positioned onthe “recessed” portion of the window frame. Pull the window down until it rests just behind the front flange of the (top) “L” shaped mounting bracket (See Fig. 5). • Expand the shutter frames (fully) on each side and secure thetop of the frames to the window sash using one 3/4” screw oneach side and one in the “L” shaped mounting bracket (Fig. 5). • Secure the shutter clamp on each side of the (lower) shutter andsecure to window sill using one 3/4” screw on each side (Fig. 5). • Place the second foam sealing strip to fit the opening betweenthe inside and outside windows, then attach the safety lock to the outside window frame using one 3/4” screw (See Fig. 6). PLEASE NOTE: Window applications come in a variety of different styles. Therefore, it may be necessary to modify orimprovise your particular installation. Window sash “L” ShapedMountingBracket Shutter clamps 3/4” screws Fig. 5 Safety Lock 3/4” screw Foam Seal Fig. 6 OPERATING INSTRUCTIONS SELECTOR SWITCH: The selector switch controls fan speed and/or cooling speed. To set desired cooling temperature, simply rotate the SELECTOR knobto the appropriate setting. FAN SPEEDS: • LOW FAN will circulate air at minimum speed without cooling. • HIGH FAN will circulate air at maximum speed without cooling. COOLING MODES: • LOW COOL provides cooling with minimum air circulation. Recommended for night-time use. • HIGH COOL provides cooling with maximum air circulation. Recommended for quick cooling or for extremely hot days. Once room iscooled, reduce setting to LOW COOL. • OFF shuts-down the unit completely NOTE: Always allow 3 minutes before switching from one mode to another. THERMOSTAT: The thermostat automatically controls the (compressor) cooling cycle and maintains the selected room temperature...