valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
This will raise the L bracket as shown in Fig. 8. Fig.8 3/4''Clearance Storm window frame Inner sill Foam 3/4'' Screw 3/4'' Screw 3/4 screw 3/4 screw 2/5 screw 3/4 screw 3/4 screw 3/4 screw 3/4 screw Mode Timer Fan Airconditioner 3/4 screw Thermostat knob Mode knob When using FAN control, turn slowly allowing unit to adjust. When using THERMOSTAT, be sure to allow three minutes before changing temperature. Adjusting too quickly may cause an overload resulting in a blown fuse. ! CAUTION ! MODE Fig.9 Fig.10 The mode knob controls fan speeds and cooling speeds. To set desired cooling temperature, simply rotate the mode knob dial to the appropriate setting. See Fig. 9. LOW FAN will circulate the air at a minimum speed without cooling. HIGH FAN will circulate the air at a maximum speed without cooling. LOW COOL provides cooling, automatically with minimum air circulation. Recommended for nighttime use. HIGH COOL provides cooling, automatically with quick cooling or for extremely hot days. Once room is cooled, reduce setting to LOW COOL. NOTE: After setting the mode, allow 3 minutes before switching to another mode. OFF will completely shut-off the unit. THERMOSTAT The thermostat automatically controls the cooling cycle (compressor) of the air conditioner to maintain room temperature. However, the fan motor will continue to operate after the compressor (cooling cycle) is completed. See Fig.9. Operating Instructions 9 Mechanical control model Fresh Air Vent Lever Fresh Air Ventilation is usually kept in the closed position. Use only when clearing smoke and/or odors from the room. Pull to open. (See Fig.10). Operating Instructions 10 Mode button Each time the Mode button is pressed, the operation mode is changed in sequence: COOLING FAN ONLY ENERGY SAVING COOLING NOTE: After setting the mode, allow 3 minutes before switching to another mode. In the FAN ONLY Mode , Room Temperature display range is from 0 (32 ) to 38 (99 ). Room Temperature below 32 ,the Temperature display L0. Room Temperature above 99 ,the Temperature display H1. NOTE: Temperature setting range is from 19 (66 ) to 31 (88 ). Fan Speed button Used to select fan speed in sequence auto, low, medium and high(low and medium are in same fan speed). Timer button Used to set or cancel timer operation. When the unit is in operation, you can set OFF Timer. When the unit is off, you can set ON Timer. Timer setting range is 0 to 24 hours. If the OFF Timer is set, the timer LED displays the remaining time to turn off the unit for only 12 seconds, then LED shifts to display set temperature. If you press Timer button within the 12 seconds, OFF Timer will be canceled. If the ON Timer is set, the timer LED displays the remaining time to turn on the unit. If you want to cancel ON TIMER, press Timer button. Used to set room temperature in COOLING mode or used to set time in Timer mode. If the two keys are pressed at the same time ,the temperature LED display will alternate between and . button The air conditioner will be started when it is energized or will be stopped when it is in operation, if you press this button. You can easily operate this air conditioner by pressing the relevant Control Panel button on the control panel as well as the remote control. Above LED lights on when the relevant mode is in used. Button Control Panel Mode Timer Airconditioner High fan speed Medium fan speed Low fan speed Auto fan speed Cooling Fan only Display set temp Display set timer Timer Energy-saving Indication symbols of LED on control panel : Fan Speed Heating Saver Mid Mode Auto High Low Timer 11 2 1 2 3 8 9 8 7 3 5 6 4 1 BUTTON Mode BUTTON Timer BUTTON The appliance will be started when it is energized or will be stopped when it is in operation, if you press this butto...
Questo manuale è adatto anche per i modelli :Condizionatori - AAW-05CM1FHUE (5.53 mb)
Condizionatori - AAW-05CM1FHUE (5.53 mb)
Condizionatori - AAW-05CR1FHUE (5.53 mb)
Condizionatori - AAW-06CM1FHUE (5.53 mb)