valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
Press the drain pipe into the hole by pushing down and away from the fins to avoid injury. (See Fig.1) Optional (CW3H02502B) 1. Remove the rubber plug and slide the chassis out from the cabinet. (See Fig. 2) 2. Install the drain pan over the corner of the cabinet where you removed the plug with 4 (or 2) screws. (See Fig.3) 3. Connect the drain hose to the outlet located at the bottom of the drain pan. You can purchase the drain hose or tubing locally to satisfy your particular needs. (Drain hose is not supplied). (See Fig.3) 4. Select the most appropriate connection from among the figures to the right (by considering the hole of the unit) to fit drain pan to your own unit. (See Fig.3) 5. Slide the chassis back into the cabinet. Reinstall the cabinet screws. Secure the cabinet to chassis by using screws. (See Fig.4) 7 About the Controls on the Air Conditioner CLOSE VENT OPEN Part A Part B Drain pipe Drain cap Controlled manually Controlled by Remote Controller OFF/ON OPERATION TEMP/TIMER COOL FAN HIGH MED LOW MODE FANSPEED SET TIMER SET/ CANCEL AIRSWINGECONOMY hr F Wireless RemoteControl Remove the rubber plug OFF/ON OPERATION TE P/TI COOL FAN HIGH MED LOW MOE FANSPEED SET TIMER SET/ CNE AIR ECONOMY F Wireless RemoteControl Fig. 4 Fig. 3 Fig. 2 Fig. 1 DRAIN HOSE Inside diameter 17mm (5/8") CABINET SCREW DRAIN PAN Additional controls and important information. Ventilation The ventilation lever must be in the CLOSE position in order to maintain the best cooling conditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is drawn out. NOTE: Before using the ventilation feature, and prior to installing the front grille, pull down part until level with part . Air Direction The direction of air can be controlled wherever you want to cool by adjusting the horizontal louver and the vertical louver. The vertical air direction is adjusted by rotating the horizontal louver forward or backward manually. The horizontal air direction is adjusted by rotating the vertical louver right or left manually or by Remote Controller. • VERTICAL AIR-DIRECTION CONTROL • HORIZONTAL AIR-DIRECTION CONTROL 8 About the Controls on the Air Conditioner Care and Maintenance Air Filter Cleaning The air filter behind the front grille should be checked and cleaned at least once every 2 weeks or more often if necessary. TO REMOVE: 1. Open the inlet grille upward by pulling out the bottom of the inlet grille or downward by pulling out the top of the inlet grille. 2. Using the tab, pull up slightly on the filter to release it and pull it down or up. 3. Clean the filter with warm, soapy water under 40°C (104°F). 4. Rinse and gently shake the water from the filter and let it dry before replacing it. CAUTION: DO NOT operate the air conditioner without a filter because dirt and lint will clog it and reduce performance. TURN THE AIR CONDITIONER OFF AND REMOVE THE PLUG FROM THE POWER OUTLET. 1. Remove the cover from the back of the remote controller. 2. Insert two AAA dry cell batteries. • Be sure that the (+) and (-) directions are correct. • Be sure that both batteries are new. 3. Re-attach the cover. • Do not use rechargeable batteries. Such batteries differ from standard dry cells in shape, dimensions, and performance. • Remove the batteries from the remote controller if the air conditioner is not going to be used for an extended length of time. HOW TO INSERT BATTERIES 9 Features and Installation Features Learning parts name prior to installation will help you understand the installation procedure. Features CABINET FRONT GRILLE AIR FILTER AIR INTAKE (INLET GRILLE) AIR DISCHARGE VERTICAL AIR DEFLECTOR (HORIZONTAL LOUVER) EVAPORATOR CONTROL BOARD REMOTE CONTROLLER POWER CORD BASE PAN CONDENSER COMPRESSOR BRACE HORIZONTAL AIR DEFLECTOR (VERTICAL LOUVER) Features and I nstallation Features and Installation Installation How to Install the Unit 1. To prevent vibration and noise, make sure the unit is installed securely and firmly 2. Install the unit where the sunlight does not shine directly on the unit. 3. The outside of the cabinet must extend outward for at least 12" (30.5cm) and there should be no obstacles, such as a fence or wall, within 20" (50.8cm) from the back of the cabinet because it will prevent heat radiation of the condenser. Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner. CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. 4. Install the unit a little slanted so the back is slightly lower than the front (about 1/2"(12.7mm)). This will force condensed water to flow to the outside. 5. Install the unit with the bottom about 30"~60"(76.2~152.4cm) above the floor level. 30"~60"(76.2~152.4cm)About 1/2"(12.7mm) Awning Cooled air Fence Over 20"(50.8cm) Heat radiation 27" to 39" (68.6~99.1cm) Offset 1/2" to 11/4" (12.7~31.8mm) Sill Exterior Interior wall 23 5/8" min.(60cm) (Without frame ...