valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
If this is not the case, have the plug replaced; • The mains socket is adequately earthed. Failure to follow these important safety instructions absolves the manufacturer of all liability. The power cable must be replaced by a qualified professional only. B Thanks to the locking pins, it’s possible to use the window bracket also for sliding windows. Position the hole of the bracket so to allow a correct installation of the exhaust hose (see figure C). A 1 2 D C • If you have a double window, use the sucker provided to hold the two parts of the window together (fig. D). 134 5,25 in. in the window pane in the wall: it is recommended that you insulate a section of the wall using suitable insulation. in the wooden kickboard of a French window F Preparing for use MAX 39 in MAX100 cm MIN 14 in MIN 35 cm SEMI-PERMANENT INSTALLATION If required, your appliance can also be installed semi-permanently (Fig. E). Proceed as follows: • Drill a hole o 5,25 inches (o 134 mm) in an outside wall or through a window pane. Respect the dimensions and height of the hole given in figure F and G. • Fit the wall flange into the hole. • Fit the air exhaust hose in the relevant hose located on the rear side of the appliance (fig. A page 5). • Fit the end of the hose to the wall flange 11 as shown in fig. G. 13 13 11 G When the hose (9) is not fitted, the drilled hole can be closed with the flange cap (11). NOTE: When installing the air conditioner semi-permanently, you should leave a door slightly open as little as 1/2 “ (1 cm) to guarantee correct ventilation. 6 11,8 in 30 cm 11,8 in 30 cm E Keep the air hoses as short and free of curves as possible to avoid constrictions. As special tools are required for installation, we suggest you let install the appliance by specialized personnel. Control panel THE CONTROL PANEL 12 1 6 8 9 2 5 3 4 7 11 10 12 13 14 15 16 16 DESCRIPTION OF THE CONTROL PANEL 1 Air conditioning symbol 9SLEEP symbol 2 Dehumidifying symbol 10 AUTOFAN indicator 11 Speed indicator 3 Fan symbol 12 MODE button (selects the modes) 4 SMART symbol 13 BOOST button 5 BOOST symbol 14 FAN button 15 ON/Standby button 6Temperature indicator 16 Increase (+) and decrease (-) 7 Timer symbol temperature button 8 Alarm symbol OPERATING FROM THE CONTROL PANEL The control panel enables you to manage all the main functions of the appliance, but to fully exploit its potential, you must use the remote control unit. TURNING THE APPLIANCE ON • Plug into the mains socket. Two lines appear on the display indicating that the appliance is in standby mode. •Press the (15) button until the appliance comes on. The last function active when it was turned off will appear. Never turn the air conditioner off by unplugging from the mains. Always press the . button, then wait for a few minutes before unplugging. This allows the appliance to perform a cycle of checks to verify operation. Operation AIR CONDITIONING MODE Ideal for hot muggy weather when you need to cool and dehumidify the room. To set this mode correctly: •Press the MODE button a number of times until the air-conditioning symbol appears. • Select the target temperature by pressing the or button until the corresponding value is displayed. • Select the required fan speed by pressing the FAN button. Four speeds are available: Maximum speed: to achieve the target temperature as rapidly as possible Medium speed: reduces noise levels but still maintains a good level of comfort Low speed: for silent operation AUTO: the appliance automatically selects the most suitable fan speed in relation to the temperature set on the digital display. The most suitable temperature for the room during the summer varies from 75°F to 81°F (24 to 27°C). You are recommended, however, not to set a temperature much below the outdoor temperature. DEHUMIDIFYING MODE Ideal to reduce room humidity (spring and autumn, damp rooms, rainy periods, etc). In dehumidifying mode, the appliance should be prepared in the same way as for air conditioning, with the air exhaust hose attached to enable the moisture to be discharged outside. To set this mode correctly: •Press the MODE button a number of times until the dehumidifying symbol appears. In this mode, fan speed is selected automatically by the appliance and cannot be set manually. Operation FAN MODE When using the appliance in this mode, the air hose does not need to be attached. To set this mode correctly: •Press the MODE button a number of times until the fan symbol appears. • Select the required fan speed by pressing the FAN button. Three speeds are available: Maximum speed: for maximum fan power Medium speed: reduces noise levels but still maintains a good level of comfort Low speed: for silent operation In this mode, AUTO speed cannot be selected. SMART MODE The appliance chooses automatically whether to operate in air conditioning or fan. Fan speed is also set automatically according to the conditions. To set this mode: •Press the MODE button a number of times until the S...