valutazioni - , GPA: ( )

Istruzioni per l'uso Broan, Modello 170F

Produttore : Broan
File Size : 118.27 kb
File Nome : ff7c2b1a-68ed-40dc-9ab7-406b534d8bbd.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

FOR SAFETY, THIS PRODUCT MUST BE GROUNDED. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN. 2. WHEN WIRING, SERVICING OR CLEANING THIS UNIT, TURN OFF POWER AND LOCK OUT SERVICE PANEL. FAILURE TO DO SO COULD ALLOW OTHERS OR THERMOSTAT TO TURN ON POWER UNEXPECTEDLY WHICH MAY CAUSE FATAL ELECTRICAL SHOCK. 3. To avoid electrical shock: • DO NOT install unit in a tub or shower enclosure or any location where it may come in contact with water. • NEVER place a switch where it can be reached from a tub or shower. 4. DO NOT install this unit in an area where chemicals or other flammables are stored or used. Explosion and fire may result. ! CAUTION 1. This product may ONLY be installed horizontally in a wall. DO NOT MOUNT IN ANY OTHER POSITION. 2. Install heater at least 6” from floor or any adjacent vertical surface. 3. DO NOT locate heater behind a door, furniture, drapes, etc., where the air flow to the unit would be restricted. 4. Provide heater with an appropriately-rated electrical circuit to prevent tripped breakers or blown fuses. (See chart below). 5. DO NOT CONNECT HEATER TO DIMMER SWITCH OR SPEED CONTROL. 6. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc., off power unit. 7. Please read specification label on product for further information and requirements. PLAN THE INSTALLATION This wall heater finish assembly is intended for installation into a Broan Model 171H rough-in housing — after the wall has been completed. The heater can be operated using the Broan Model 86 Line- Voltage Thermostat from a wall location or the Broan Model 83 Integral Thermostat installed into heater. Purchase the control separately. The table below lists the ratings for each model. MODELS VOLTS AMPS WATTS BTU/HR 120 8.33/4.16 1000/500 3413/1707 170F 240 4.16 1000 3413 208 3.61 750 2560 120 12.5/6.25 1500/750 5120/2560 174F 240 6.25 1500 5120 208 5.41 1125 3640 178F 240 208 8.33/4.16 7.21/3.61 2000/1000 1500/750 6827/3413 5120/2560 BOLD ratings are factory wired. See "OPTIONAL WIRING CONVERSIONS" section on pages 2 and 3 for wattage and voltage conversion instructions. Follow these basic steps when installing this heater: • Remove the housing mask. • Fasten finish assembly inside housing. • Plug assembly in. • Attach grille. WALL STUD POWER CABLE GRILLE HEATER HOUSING DRYWALL INSTALL THE HEATER ASSEMBLY 1. Remove housing mask. Make sure wall has been finished (including paint or wall paper, etc.) Take out and discard the cardboard mask from inside of housing. TABS FASTEN TO HOUSING WITH RETAINING SCREW - HERE 2. Install heater assembly into housing. Place element end of heater assembly behind the tabs on the left side of housing. Pivot the assembly in and fasten with retaining screw from parts bag. Plug wiring harness into receptacle. 3. Provide desired control. The heater finish assembly has no adjustable thermostat control. If a wall-moun...