valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Replace cracked or damaged bit immediately. 3.Avoid cutting nails. Inspect for and remove all nails from the workpiece be- fore operation. 4. Hold the tool firmly with both hands. 5. Keep hands away from rotating parts. 6. Make sure the bit is not contacting the workpiece before the switch is turned on. 7. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate improperly installed bit. 8. Be careful of the bit rotating direction and the feed direction. (cf. P. 7) 9. Do not leave the tool running. Operate the tool only when hand-held. IO.Always switch off and wait for the bit to come to a complete stop before removing the tool from workpiece. 1 1. Do not touch the bit immediately after operation; it may be extremely hot and could burn your skin. 12. Keep the bit retracted so as not to protrude from the tool base except dur- ing actual operation. SAVE THESE INSTRUCTIONS. Installing or removing router bit CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the bit. Insert the bit all the way into the collet cone and tighten the collet nut securely with the two wrenches. To remove the bit, follow the installation Tighten procedure in reverse. t CAUTION : Do not tighten the collet nut without inserting a bit, or the collet cone will break. Adjusting depth of cut Place the tool on a flat surface. Loosen the screw securing the stopper pole. Loosen the lock lever and lower the tool body until the bit just touches the flat surface. Tighten the lock lever to lock the tool body. Next, lower the stopper pole until it makes contact with the adjusting hex bolt. Align the depth pointer with the "0" graduation. Raise the stopper pole until the desired depth of cut is obtained. The depth of cut is indicated on the scale (1 mm or 1/16" per graduation) by the depth pointer. Then tighten the screw to secure the stopper pole. Now, your predetermined depth of cut can be obtained by loosening the lock lever and then lowering the tool body until the stopper pole makes contact with the adjusting hex bolt. CAUTION: Since excessive cutting may cause overload of the motor' or difficulty in controlling the tool, the depth of cut should not be more than (5/8")at a pass when cutting grooves with a (1/4") diameter bit. [Note: When cutting grooves with an (3/4") diameter bit, the depth of cut should not be more than (1/4") at a pass.] When you wish to cut grooves more than (5/8")deep with a (1/4") diameter bit or more than (1/4") deep with an (3/4") diameter bit, make several passes with progressively deeper bit settings. Stopper block The stopper block has three adjusting hex bolts which raise or lower 0.8 mm (about 1/32") per turn. You can easily obtain three different depths of cut using these adjusting hex bolts without readjusting the stopper pole. Adjust the lowest hex bolt to obtain the deepest depth of cut, following the method of "Adjusting depth of cut". Adjust the two remaining hex bolts to obtain shallower depths of cut. The differences in height of these hex bolts are equal to the differences in depths of cut. To adjust the hex bolts, first loosen the hex nuts on the hex bolts with the wrench and then turn the hex bolts. After obtaining the desired position, tighten the hex nuts while holding the hex bolts in the desired position. The stopper block is also convenient for making three passes with progressively deeper bit settings when cutting deep grooves. Adjusting lock lever The locked position of the lock lever is adjustable. To adjust it, loosen the lock lever 3/4 turn and press the center of the lock lever. The hex nut will come out. Set the hex nut to the desired position and tighen the lock lever. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION: Before plugging in the tool, always check to see that the trigger switch actuates pro- perly and returns to the "OFF" position when released. Operation *Set the tool base on the workpiece to be cut without the bit making any contact. Then turn the tool on and wait until the bit attains full speed. Lower the tool body and move the tool forward over the workpiece surface, keeping the tool base flush and advancing smoothly until the cutting is complete. When doing edge cutting, the workpiece surface should be on the left side of the bit in the feed direction. (See the figure below) Feed direction r__-,~.. ///,'/!3it revolving direction 7, (View from the top of the tool) v Correct bit feed direction NOTE : Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. Moving the tool forward too slowly may burn and mar the cut. The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of scrap lumber. This will show exactly how the cut will look as well as enable y...