valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
Failure to do so will result in damage to the collet chuck. 2. Removing bits When removing the bits, do so by following the steps for installing bits in reverse order. Motor Housing Base Lever Wrench Bit Collet Chuck 16mm Loosen Tighten Wrench Fig. 3 English INSTALLING THE MOTOR HOUSING WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle to avoid serious trouble. 1. Installing the motor housing (1) Open the lever. (2) While holding the base, insert the motor housing into the base aligning the pin with the groove in the base. (3) Confirm that the pin and the groove are aligning. Rotate the motor housing Lever clockwise into the base. (4) Close the lock lever. CAUTION: You should be able to clamp the locking lever without excessive force. Excessive force may damage the base. You should not be able to move the motor in the base when the lever is clamped. To adjust the lever’s clamping force, open the locking lever and turn the knob nut in small increments. Turning the knob nut clockwise tightens the lever, while turning the knob nut counterclockwise loosens the lever. HOW TO USE THE ROUTER WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle to avoid serious trouble. 1. Adjusting depth of cut (1) Place the tool on a flat wood surface. (2) Open the lever and turn the motor housing until the bit just touches the flat surface. (Fig. 5) (3) Clamp the lever down until the point where a click can be felt. (Fig. 6) NOTE: The motor housing can be temporarily secured by clamping the lever (the motor housing does not slide down by its own weight). If the motor housing slides down, make adjustments by tightening the knob nut. Turning the knob nut clockwise tightens the lever, while turning the knob nut counterclockwise loosens the lever. Motor Housing GroovePin Knob Nut Base Fig. 4 Motor Housing Index Line Graduation Scale Ring Base Lever Fig. 5 Knob Nut Lever Fig. 6 English (4) While holding up the base slightly, turn the motor housing clockwise until the index line on the motor housing reaches the desired depth indicated on the scale ring. (Fig. 5) (5) Close the lever firmly. 2. Adjusting the rotation speed (Model M12VC only) The M12VC have an electronic control system that allows stepless rpm changes. As shown in Fig. 7 dial position “1” is for minimum speed and position “6” for maximum speed. 3. Centering the template guide adapter WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle to avoid serious trouble. (1) Loosen the 2 template guide adapter screws, so that the template guide adapter can be moved. (Fig. 8) (2) Insert the centering gauge through the hole in the template guide adapter and into the collet chuck. (Fig. 9) (3) Tighten the collet chuck by hand. (4) Tighten the lever. (This aligns the center of the template guide adapter.) (5) Tighten the template guide adapter screws, and pull out the centering gauge. Dial Fig. 7 Template Guide Adapter Screw Centering Gauge Fig. 9 Fig. 8 Template Guide Adapter Screw Collet Chuck Lever 4. Guiding the router (1) Template guide (M12VC, M12SC: Optional accessory) Use the template guide when employing a template for producing a large quantitiy of Template identically shaped products. (Fig. 10) As shown in Fig. 11, to install insert template guide in center hole in template guide Lock Nut adapter and secure in place with the lock nut. A template is a profiling mold made of plywood or thin lumber. When making a template, pay particular attention to the Template Template matters cescribed blow and illustrated in Guide Guide Adapter Fig. 12. Fig. 10 Fig. 11 English When using the router along the interior plane of the template, the dimensions of the finished product will be less than the dimensions of the template by an amount equal to dimension “A”, the difference between the radius of the template guide and the radius of the bit. The reverse is frue when using the router along the exterior of the template. Secure the template to the workpiece. Feed the router in the manner that the template guide moves along the template as shown in Fig. 12. (2) Straight guide (optional accessory) Use straight guide for chamfering and groove cutting along the materials side. 1 Insert the guide bar into the hole in the bar holder, then lightly tighten the 2 wing bolts (A) on top of the bar holder. 2 Insert the guide bar into the hole in the base, Hex then firmly tighten the 2 hex socket bolts Bolt (standard accessories). 3 Make minute adjustments of the dimensions between the bit and the guide surface with the feed screw, then firmly tighten the 2 wing bolts (A) on top of the bar holder and the wing bolt (B) that secures the straight guide. (Fig.13) 4 As shown in Fig. 14, securely attach the bottom of the base to processed surface of the materials. Feed the router while keeping the guide plane on the surface of the materials. 5. Cutting WARNING: . Wear eye protection when operating this tool. A Template Gui...
Questo manuale è adatto anche per i modelli :Falegnami piastra - KM 12VC (1.56 mb)
Falegnami piastra - M 12SC (1.56 mb)
Falegnami piastra - M 12VC (1.56 mb)