valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
Full mental alertness is required at all times when running a machine. 21. NEVER ALLOW UNSUPERVISED OR INEXPERIENCED PERSONNEL TO OPERATE THE MACHINE. Make sure any instructions you give in regards to machine operation are approved, correct, safe, and clearly understood. 22. IF AT ANY TIME YOU ARE EXPERIENCING DIFFICULTIES performing the intended operation, stop using the machine! Then contact our service department or ask a qualified expert how the operation should be performed. -4- G1182 6" Series Jointers Additional Safety Instructions For Jointers 1. JOINTING SAFETY BEGINS with your lumber. Inspect your stock carefully before you feed it over the cutterhead. If you have any doubts about the stability or structural integrity of your stock, DO NOT JOINT IT! 2. MAINTAIN PROPER RELATIONSHIPS of infeed and outfeed table surfaces and cutterhead knife path. 3. ALWAYS USE A PUSH BLOCK when jointing. Never place your hands directly over the cutterhead. 4. SUPPORT THE WORKPIECE adequately at all times during operation, maintain control over the work at all times. 5. WHEN JOINTING, do not stand directly at the end of either table. Position yourself just to the side of the infeed table to avoid possible kickbacks. 6. NEVER MAKE JOINTING CUTS deeper than 1.8". 7. NEVER JOINT A BOARD that has loose knots. All defects should be cut out of the board before it is planed or jointed. 8. NEVER JOINT end grain. 9. JOINT WITH THE GRAIN. Jointing against the grain is dangerous and could produce chatter or excessive chip out. 10. WITH THE EXCEPTION OF RABBETING, all operations must be performed with the guard in place. After rabbeting, be sure to replace the guard. 11. NEVER BACK THE WORK toward the infeed table. 12. HABITS – GOOD AND BAD – are hard to break. Develop good habits in your shop and safety will become second-nature to you. 13. “KICKBACK” is when the workpiece is thrown off the jointer table by the force of the cutterheads. Always use pushblocks and safety glasses to reduce the likelihood of injury from “kickback.” If you do not understand what kickback is, or how it occurs, Do Not operate this machine. 14. BE AWARE THAT CERTAIN WOODS MAY CAUSE AN ALLERGIC REACTION in people and animals, especially when exposed to fine dust. Make sure you know what type of wood dust you will be exposed to and always wear an approved respirator. No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results. G1182 6" Series Jointers -5 SECTION 2: CIRCUIT REQUIREMENTS 110V Operation The Model G1182 Jointer Series is wired for 110/120V, single- phase operation. The 1 H.P. motor is dual voltage; however, we do not recommend converting to 220V because the magnetic switch is only rated for 110V. The motor will safely draw 14 amps at 110V. If you operate this machine on any circuit that is already close to its capacity, it might blow a fuse or trip a circuit breaker. However, if an unusual load does not exist and a power failure still occurs, contact a qualified electrician or our service department. A 15 amp fuse or circuit breaker should be used when fusing this (tool description). Circuit breakers rated any higher may not be adequate to protect the circuit from power surges. Extension Cords If you find it necessary to use an extension cord with the Model G1182 series of jointers, make sure the cord is rated Hard Service (grade S) or better. Refer to the chart in the standard safety instructions to determine the minimum gauge for the extension cord. The extension cord must also contain a ground wire and plug pin. Always repair or replace extension cords when they become worn or damaged. Grounding In the event of an electrical short, grounding reduces the risk of electric shock by providing electric current a path of least resistance. This tool is equipped with a power cord having an equipment-grounding conductor. See Figure 1. The outlet must be properly installed and grounded in accordance with all local codes and ordinances. This equipment must be grounded. Verify that any existing electrical outlet and circuit you intend to plug into is actually grounded. Under no circumstances should the grounding pin from any three-pronged plug be removed. Serious injury may occur. Figure 1A. Do not remove grounding pin. Figure 1. Typical 110V 3-prong plug and outlet. -6-G1182 6" Series Jointers G1182 6" Series Jointers -7- SECTION 3: INTRODUCTION We are proud to offer these four models of the Model G1182 6" Jointer. These machines are part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction. The Model G1182 Joi...
Questo manuale è adatto anche per i modelli :Falegnami piastra - G1182Z (1.84 mb)
Falegnami piastra - G1182ZX (1.84 mb)