Produttore : Shindaiwa
File Size : 1.06 mb
File Nome :
|
Facilità d'uso
WARNING! Do not make unauthorized modifications or alterations to your unit or its components. Tine Installation and Orientation Tine installation directly affects the Tiller/ Cultivator Tool’s ability to break new ground. Using the illustrations as a guide, determine the correct tine orientation for the tilling/cultivating job at hand: Install the tine assemblies to the 1. gearcase output shafts. Secure each tine assembly with 2. one clevis pin and one hitch pin as shown. Install the tine assemblies Hitch Pin Clevis Pin Clevis Pin WARNING! Always switch the engine OFF before working on the gearcase or tines! Hitch Pin Tine Assemblies (hub faces in) Weeding/Cultivating in Softer Soil Tilling/Digging in Hard Soil MCLT23006 MCLT23007 Leading Edge Out Leading Edge In Tiller Leading edge out for aggressive action in hard soils. Cultivator Leading edge in for weeding or turning softer soils. Assembly Assembling tube sections Assembling tube sections Place powerhead/lower tube 1. assembly on a clean, flat surface so that both assemblies fit end to end. The powerhead/lower tube assembly should be facing positioned with the locking hole in the tube end facing up. Slip off the protective plastic covers 2. from the ends of both tubes, and loosen the coupler screw knob. Insert the tool assembly into the 3. coupler, with the tool decal facing up, until the line of the decal is flush with the end of the coupler. Twist the tool assembly back and 4. forth until you are sure it snaps in place by the coupler latch. When the two tube halves are 5. locked together, press down on the spring-loaded latch protector and tighten the coupler screw knob. Latch protector (extended) Latch Lower tube assembly Coupler screw knob Locking hole CAUTION! Keep the open ends of the tubes clean and free of debris! The powerhead/lower tube assembly should be facing positioned with the locking hole in the tube end facing up Coupler Tool assembly Latch Protector (lowered) Coupler Coupler Screw Knob When the two tube halves are locked together, press down on the spring-loaded latch protector and tighten the coupler screw knob. Disassembling the tube sections With the unit on a clean, flat sur1. face, loosen the coupler screw. The spring-loaded coupler protector should pop up. Press down on the latch with your 2. finger or thumb. This releases the coupler lock. Pull the upper tube assembly out of 3. the coupler. Disassembling the tube sections Press latch Optional Accessories Strap and Hanger Although a strap and hanger is not required for use with this unit, it is recommended to reduce operator fatigue during extended periods of operation. Make sure all hooks and adjusting devices are secure. Adjust the harness shoulder strap so the shoulder pad rests comfortably on the off-side shoulder. Recommended Strap and Hanger Operating Checking Unit Condition NEVER operate the unit with the protective devices (ignition switch, etc.) removed! ALWAYS make sure the tool attachment is properly installed and firmly tightened before operation. Use only authorized Shindaiwa parts and accessories with your Shindaiwa Multipurpose Tool. Do not make modifications to your machine without the written approval of Shindaiwa. NEVER use a cracked or warped tine: replace it with a serviceable one. ALWAYS stop the engine immediately and check for damage if you strike a foreign object or if the machine becomes tangled. Do not operate with broken or damaged equipment. NEVER allow the engine to run at high RPM without a load. Doing so could damage the engine. NEVER operate a machine with worn or damaged fasteners or attachment holders. Starting and Fueling For detailed instructions on general safety procedures, fueling, starting, and stopping the powerhead assembly, refer to the appropriate Owner’s Manual for your machine. WARNING! KEEP CLEAR of tines during starting operations! The drums may rotate during startup. WARNING! BURN DANGER! The gearcase will become very hot during normal operation. Operating Techniques Your Shindaiwa Tiller/Cultivator Tool's reversible tines allow you to quickly change from operation as a cultivator- weeder to an aggressive tiller for quickly digging a new garden or landscaping plot. For best operation in either mode: WATER 1. the area to be tilled at least 24 hours before your planned tilling operation; then water again about 3 hours before the actual tilling. PULL 2. the tiller slowly toward you when tilling or cultivating. Use the correct method for the job: FOR DEEP TILLING¦¦ (up to 25 cm/10” depth) use full throttle while slowly rocking the tiller back and forth over the work area. SHALLOW WEEDING ¦¦in soft soils is easiest when the tines are installed in the cultivating configuration, with additional depth available by using a gentle rocking motion as described above. HEAVY WEEDS ¦¦or weeding in harder soils may require reversing the tines to the more aggressive tiller configuration. Tilling/Digging in Hard Soil MCLT23006 Leading Edge Out Til...
Questo manuale è adatto anche per i modelli :Coltivatori - 80274 (1.06 mb)
Coltivatori - 99922201031 (1.06 mb)
Coltivatori - T10812999999 (1.06 mb)
Coltivatori - T10911001001 (1.06 mb)