valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Remove the air filter cover and the air filter. 3. Wipe the cover and the inside of the air filter housing with a clean cloth. 4. Clean the air filter in a solution of water and household detergent. Rinse thoroughtly in clean water. 5. Wrap the air filter in a dry clean cloth. Squeeze out (do not twist) all solution until dry. 6. Cover the outside of the air filter with oil. Use the same type of oil as used to make the fuel mixture. Lightly squeeze the air filter to distribute and remove any excess oil. 7. Put the clean air filter into the air filter housing. 8. Install the air filter cover and secure with the screws as shown. 9. Connect the spark plug wire to the spark plug. Air Filter Cover Screw Filter Housing Figure 12 CYLINDER EXHAUST PORTS Clean the cylinder exhaust ports after every 75 hours of operation. For this procedure, we recommend that you take your unit to a Authorized Service Center. F-051302L 17 SERVICE AND ADJUSTMENT HOW TO REMOVE AND INSTALL THE TINES References to the right or left side of the cultivator are from the viewpoint of the operator’s position behind the unit. All four tines are different and cannot be interchanged. The tines must be correctly installed or the cultivator will not function properly. To till around plants or in small areas, the outside tines can be removed to reduce the tilling width to approximately 7 inches. WARNING: The tines are self sharpening and will become quite sharp from use. Handle carefully. The tines will all wear evenly. If the tines are being replaced because of wear, we recommend that all four tines be replaced at the same time. To replace the tines, do the following: Tine Removal 1. Put the on-off switch in the OFF position. 2. Disconnect the spark plug wire from the spark plug. 3. While wearing gloves, remove the hairpins and clevis pins that secure the tine assemblies to the shaft (see Figure 13). Remove the tines from one side of the unit. ClevisPinsHair Pins Figure 13 Tines Tine Installation 1. Clean and lubricate the tine shaft with a few drops of oil. 2. Place the inside tine on the tine shaft and reinstall the clevis pin and hairpin. 3. When the tines are properly installed, the letter R will be visible on the outside of the right tine (see Figure 14). The letter L will be visible on the outside of the left tine. Figure 14 R 4. Mount the outside tine on the tine shaft and fasten with the clevis pin and hairpin (see Figure 13). 5. The cutting tips on the outside tines all bend in toward the inside tine. When assembled correctly, the letter R on the right side, or L on the left side, will be visible from the outside of the unit. 6. Repeat the above steps on the opposite side of the unit. NOTE: Make sure the tines are installed on the correct side of the unit. F-051302L 18 SERVICE AND ADJUSTMENT HOW TO ADJUST THE CARBURETOR A dirty air cleaner will cause the engine to run improperly or to smoke excessively. Before adjusting the carburetor, make sure the air cleaner is clean. Never make unnecessary adjustments to the carburetor. The carburetor was set at the factory to operate efficiently under most applications. However, if adjustments are required, we recommend you contact an Authorized Service Center. If you feel that you are competent to make carburetor adjustment proceed as follows. 1. Lower the wheels to the transport position. 2. Locate the idle speed adjustment screw (see Figure 15). Turn the idle adjustment screw 1/4 turn counterclockwise (to the left). 3. Start the engine and release the throttle control. 4. Tilt the cultivator back on the wheels or stake so that the tines are off the ground. In correct adjustment, the tines will not rotate when the throttle is released. If the tines turn, repeat step 2. WARNING: The engine governor is set at the factory. Do not change the governor setting. Over speeding the engine above the factory setting can be dangerous. If you think the engine governor needs an adjustment, contact an Authorized Service Center. Carburetor Idle Speed Adjustment Screw Carburetor is located between the fuel tank/air filter and the engine. Engine Shown With Fuel Tank Removed Figure 15 F-051302L 19 SERVICE AND ADJUSTMENT STORAGE WARNING: Never store the cul. Cover the cultivator with a suitable protivator indoors with fuel in the tective cover that does not retain moisfuel tank. Never store in an enture. Do not use plastic. closed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, water heater or clothes dryer. WARNING: Do not remove gas oline while inside a building, near a fire, or while you smoke. Gasoline fumes can cause an explosion or a fire. When the cultivator is put in storage for thirty days or more, follow the steps below to make sure the cultivator is in good condition the following season. Cultivator . Completely clean the cultivator. . Remove the tines. Clean and apply oil to the tine shafts. Mount the tines onto the tine shafts. See “How To Remove An...