valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
The job consists of removing the old cutterhead, installing and shimming the new spiral cutterhead, and readjusting the outfeed table even with the carbide inserts at TDC (top dead center). Call Technical Support at (570) 546-9663 if you need help. the t10125 spiral cutterhead is only designed to be used with the grizzly model g0452 6" Jointer. do not install this cutterhead in any other jointer model or make. doing so could result in property damage or serious personal injury. recommended tools Wrench 17mm.................................................... 1 precision straightedge (figure 1)..................... 1 Feeler Gauge set .............................................. 1 pair of heavy leather Gloves ........................... 1 g9644—12" precision straightedge h2675—16" precision straightedge is your straightedge really straight? These grade 00 heavy-duty stainless steel straightedges are manufactured to Din874 standards for professional results in set-up and inspection work. figure 1. precision straightedges. inventory (figure 2) a. spiral Cutterhead ....................................... 1 b. Torx Drivers T20 ........................................ 2 c. Flat head Torx screws T20 M6-1 x 15......3 d. indexable Carbide inserts 14 x 14 x 2 ....... 5 e. Torx l-Wrenches T20 (not shown) ............ 2 a D C B figure 2. spiral cutterhead inventory. CopyriGhT © july, 2008 By Grizzly inDusTrial, inC. Warning: no portion of this manual may be reproduced in any shape or form Without the Written approval of grizzly industrial, inc. #Bl10874 prinTeD in China installation 6. Wearing heavy leather gloves, carefully remove the cutterhead from the casting (see 1. DisConneCT joinTer FroM poWer! figure 5). 2. remove the jointer fence and cutterhead note: Your cutterhead may have paper shims guard. stuck to the bearing block or the part of the casting where the bearing block rests. These 3. remove the V-belt from the pulleys. were included at the factory when they calibrated your cutterhead even with the outfeed 4. lower both beds to make enough room for table. If you see these, carefully pull them the cutterhead to come out, as shown in off and set them aside for later use, or keep figure 3. them with your cutterhead in the event that you reinstall it later. Also, mark the side of note: When lowering, make sure that the the cutterhead where they were used, so fence support does not come in contact with the future install will go smoothly. Your new the cutterhead pulley. cutterhead may or may not need these. figure 3. example of jointer disassembly steps 1–4. figure 5. example of cutterhead removed. Bearing Block stud Bearing Block 7. remove the bearing block studs from the 5. remove the nut and lock washer on the bear- bearing blocks. ing block stud, as shown in figure 4, and repeat on the other side. 8. use a pulley puller to remove the pulley, remove the key from the cutterhead, then use an arbor press to remove the bearings and bearing blocks from the cutterhead. 9. reinstall the bearings removed in step 8 onto the bearing blocks, and install the bearing blocks onto the cutterhead with an arbor press or by gently tapping with a block of wood and a rubber dead blow hammer. 10. reinstall the key onto the keyway, then press the pulley onto the new cutterhead shaft. 11. reinstall the bearing block studs onto the bearing blocks. figure 4. example of removing nut and lock washer on bearing block stud. -2 T10125 6" spiral Cutterhead 12. install the cutterhead (figure 6) with the lock washers and hex nuts removed in step 5. figure 6. example of spiral cutterhead installed. 13. Tighten the spiral cutterhead in place, and ensure both pulley setscrews are tight. 14. using the straightedge and feeler gauge set, inspect the cutterhead parallelism with the outfeed table as shown in figure 7. With the straightedge in position, raise or lower the outfeed table until the cutterhead body (not the carbide insert) just touches the straightedge. .................................................. figure 7. Checking cutterhead parallelism. 15. Move the straightedge to the other side to determine if one end of the cutterhead body is higher/lower than the other. (place the feeler gauge between the cutterhead body and the straightedge to determine the height difference.) —if the cutterhead is even or within 0.004" with the outfeed table from one side to the other, skip to step 18. —if the cutterhead is over 0.004" from one side to the other, go to step 16. 16. loosen the hex nuts securing both bearing block studs, lift the spiral cutterhead slightly, then place a shim beneath the bearing block that needs to be adjusted. note: Use the shims from your old cutterhead if available. If not available, newspaper is approximately 0.003" thick and will work for shimming (we don't recommend shimming more than 0.004" on either side, as this may affect how the bearing block seats in the casting). 17. repeat steps 14–16 and adjust if necessary, th...