Log:
valutazioni - 3, GPA: 4.3 ( )

Istruzioni per l'uso Hobart, Modello 2912 ML-104964

Produttore : Hobart
File Size : 927.41 kb
File Nome :
Lingua di insegnamento: enfr
Vai a scaricare



Facilità d'uso


3). Adjust the Gauge Plate by turning the Index Knob (Fig. 3) to obtain the desired slice thickness. The numbers on the Index Knob do not indicate actual measurements but may be used for reference to duplicate slice thickness. Turn the slicer on by pulling the Switch Knob (Fig. 3) forward until it starts and then releasing it. Unless the Gauge Plate is opened before pulling the Switch Knob on, the slicer will not continue to run when the Switch Knob is released. Use either Carriage Tray Handle (Fig. 3) to push the Carriage back and forth to slice manually. Turn the slicer off by pushing the Switch Knob or by closing the Gauge Plate. To operate the slicer in Automatic mode . . . Rotate the Speed Selector Knob (Fig. 3) to the desired speed; make sure the Carriage is in HOME position (all the way forward); make sure the Lever (Fig. 3) is on the Manual position (pointing down); turn the slicer on; start the carriage drive unit by rotating the Lever to the Automatic position (up and to the right). Any of the six speed selections can be used to begin Automatic mode. The speed can be adjusted at any time by rotating the Speed Selector Knob. To stop the drive unit, rotate the Lever down and to the left — to the Manual position. To use the optional Food Chute, place the Meat Grip on the Retaining Clip, fit the hangers on the Food Chute around the meat grip slide rod (at front), and lower the Food Chute onto the Carriage Tray. SWITCH KNOB SPEED SELECTOR KNOB LEVER IN MANUAL (DOWN) POSITION LATCH KNOB GAUGE PLATE TOP KNIFE COVER CARRIAGE TRAY SHARPENER INDEX KNOB CARRIAGE HANDLES MEAT GRIP RETAINING CLIP Model 2912 PL-41257-1 Fig. 3 – 5 – This machine must be thoroughly cleaned and sanitized after each day’s operation or after being idle for an extended period of time. WARNING: THE SLICER KNIFE IS VERY SHARP. TOP KNIFE COVER EXERCISE EXTREME CAUTION WHEN WORKING NEAR THE KNIFE. WARNING: UNPLUG MACHINE POWER CORD AND TURN THE INDEX KNOB FULLY CLOCKWISE BEFORE CLEANING THE SLICER. Use a clean cloth soaked in mild detergent and warm water to wipe all surfaces of the machine. Rinse using a fresh cloth and clean water. Use only PL-41258-1 products formulated to be safe on stainless steel or Fig. 4 aluminum. To clean the Carriage Tray, close the gauge plate and pull the Carriage all the way to the front. Unscrew the Knob on the Carriage Tray / Support Arm (Fig. 4). Tilt the Carriage Tray / Support Arm to the right until almost horizontal (Fig. 4). The Carriage Tray / Support Arm can be cleaned while in this horizontal position, or it can be removed by grasping with both hands and lifting straight up. Once removed, the Carriage Tray / Support Arm can be cleaned in a sink. NOTE: The last three digits of the slicer serial number are etched on the Key (Fig. 8) so you can make sure the Carriage Tray stays with its own slicer. Remove the Top Knife Cover by rotating the Latch Knob (Fig. 4) counterclockwise and lifting it free of the guide pins. Remove the Deflector (Fig...

Questo manuale è adatto anche per i modelli :
Stoviglie - 2812 ML-104618 (927.41 kb)
Stoviglie - 2812 ML-104959 (927.41 kb)
Stoviglie - 2912 ML-104761 (927.41 kb)
Stoviglie - 2912 ML-104821 (927.41 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie