valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
2 II. Electrical Safeguards ....................................... 2-3 III. Specifications .................................................. 3 IV. Set-up .............................................................. 3-5 Inspection ........................................................ 3 Appropriate Location ....................................... 3 Loading Film onto Mandrels ............................ 3 Threading the Film ........................................... 4 Mandrel Tension Adjustment ........................... 4 Roller Pressure Adjustment ............................. 4 Slitters.............................................................. 5 V. Thermal Laminating ......................................... 5 VI. Pressure Sensitive Laminating ........................ 6 VII. Coating Mount Board....................................... 6 VIII. Mounting & Laminating .................................... 7 IX. Maintenance/Service ....................................... 7-8 Cleaning Rubber Rollers.................................. 8 Cleaning Heat Shoes....................................... 8 Removing Wrap-arounds ................................. 8 X. Trouble-shooting.............................................. 9 XI. Laminating & Mounting Do’s & Don’ts ............ 10 XII. Warranty & Return Policy ................................ 10 abcoffice800-658-87881 Finisher 4300 (BA-FS43) Mandrel Control Panel Upper Supply (see below) Brake Nut Feed Table Laminating/Mounting Selection Knobs Feed Table Adjustment Knob Feed Table Tie Bar Lower Supply Mandrel Guide Emergency Stop Button Safety Shield Top Supply Mandrel Holder Mandrel STANDARD LAMINATING MOUNTING CLOSED OPEN CLOSED OPEN STANDARD LAMINATING MOUNTING Left Side Cover Right Side Cover STANDARD LAMINATING MOUNTING STANDARD LAMINATING MOUNTING Control Panel FORWARD REVERSE 0 0 MOTOR SPEED CONTROL TOP HEAT SHOE TEMPERATURE CONTROL TOP BOTTOM TEMPERATURE CONTROL BOTTOM HEAT SHOE 0 HEAT 0 HEATED ROLLERS FANS 1 1 11 Core Mandrel Gripper Brake Nut abcoffice800-658-8788I. For your safety... • Do not connect the laminator to electrical power or attempt to operate it until you have read these instructions completely. Keep these instructions in a convenient location for future reference. • Read all safety messages located in this instruction manual and on the laminator very carefully. • Always replace safety shield before operating your laminator. If you service this machine yourself, ensure that the safety shield is returned to the operating position when service is completed. Do this to protect all operators. Operators may be harmed if you do not follow this instruction. • Use caution when removing the feed table as it weigh approximately 34 lbs. Removing feed table exposes hot and moving parts. This means that you can be harmed if you remove the feed table. When the table is in the proper position the risk of injury to the operator is reduced. • Do not operate this laminator without all detachable units installed correctly. This means that there is risk of injury if this product is operated without all of its parts in their proper positions. • Keep hands and clothing away from rollers. The rollers are pinch points that can trap body parts or clothing and cause serious injury. • Do not touch the heat shoes or front rollers while the laminator heater power is on. Turn rollers and shoes off allow to cool. • Do not use the laminator for other than its intended purpose. • Only operate this machine if you have been properly trained and authorized to do so. Contact the manufacturer for training information at 909-296-9780. II. Electrical Safeguards... • Never override or attempt to defeat electrical or mechanical safety interlock devices. • Disconnect power supply before servicing your laminator. This laminator uses double pole/neutral fusing. • A readily accessible disconnect device should be incorporated in the fixed wiring. • The machine has been manufactured without a plug on the power cord. We recommend that you connect this unit directly to a power main. Have a qualified electrician install your power supply for you. Care must be exercised to properly identify the neutral wire in the power cord. The neutral power cord wire is color coded white. The neutral of the power main should be identified using a suitable voltmeter. • The laminator should only be operated from the type of power source indicated in these OPERATING INSTRUCTIONS and on the serial label located on the rear panel of the unit. • Do not leave the laminator power on for extended periods while not in use. Open the panel breaker at the end of the day as a precaution against a possible fire hazard. 2 abcoffice800-658-8788• Do not operate the laminator with a damaged power supply cord or plug. • Replace fuses only with same type rated 30A, 240V and 1A, 250V fuses. Contact your dealer for replacement fuses. • There are four (4) EMERGENCY STOP b...
Questo manuale è adatto anche per i modelli :Laminator - Finisher BA-FS43 (369.6 kb)