valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
MAIN ON/OFF SWITCH (Fig. 9– Item W) The Main On/Off Switch supplies power or removes power from the machine. FUSES (Fig. 9– Item X) The Fuses protect internal PCB’s and motors. POWER CORD (Fig. 9– Item Y) The Power Cord plugs into the Main Power source or outlet. See (Machine Specs for plug requirements.) LOCKING PINS (Fig10– Item Z) The Locking Pins secure the Film Shaft Latch. FILM SHAFT LATCH (Fig. 10– Item A1) The Film Shaft Latch secures the Supply shaft ensuring that the film is supported and enters the nip accurately. PRELAMINATING FILM PERFEORATOR WHEEL (Fig. 11– Item B1) The Prelaminating Film Perforator Wheel pierces small holes into the film to ensure controlled snapping or separating of images. FILM CORE CHUCKS (Fig. 11– Item C1) The Film Core Chucks secure the film onto the Supply Shaft. FILM SUPPLY SHAFT (Fig. 11– Item D1) The Film Supply Shaft accepts a 3 inch Core Chuck. The two Core Chucks slide onto the Film Supply Shaft, supporting the film being used. The Film Supply Shaft has a ruler adhered to the shaft for ease and accuracy when aligning the film and medias. TOP FILM IDLER (Fig. 11– Item E1) The Top Film Idler guides the film through the nip giving the film adequate film dwell time. FEATURES/ACCESORIES GUIDE Figure 12 Figure 13 Figure 14 PULL ROLLERS (Fig. 12– Item F1) The Pull Rollers are silicone driven rollers that pull the film and media through the machine and into the Bursting Rollers. SKEW WHEEL (Fig. 12– Item G1) For proper “snapping” of images, the out put must have a “skew” in the paper or a raised “tent” on one side of the output. By adjusting the Skew Wheel, you can adjust the amount of “Skew” or “Tent” needed for proper “snapping”. SKEW WHEEL PRESSURE ADJUSTMENT (Fig. 12– Item G2) The Skew Wheel Pressure Adjustment can be made by turning the screw down for more pressure and up for less. SKEW WHEEL LOCK DOWNS (Fig. 12– Item G3) The Skew Wheel Lock Downs secure the Skew Wheel to the shaft. These are used to relocate the Skew Wheel as needed. IN LINE PERFORATOR WHEEL (Fig. 12– Item H1) The In Line Perforator Wheel “perfs” the edge of the film allowing the images to be “snapped” or “separated”. PERFORATOR WHEEL TENSION ADJUSTMENT (Fig. 12– Item H2) The Perforator Wheel Tension Adjustment can be made by turning the screw. PERFORATOR WHEEL LOCK DOWN (Fig. 12– Item H3) The Perforator Wheel Lock Down secures the Perforator Wheel to the shaft. This is used to relocate the Perforator Wheel as needed. OUTPUT FEED BELTS (Fig. 12– Item I1) The Output Feed Belts assist the finished images into the Burst Rollers. PAPER GUIDES (Fig. 13– Item J1) The Paper Guides catch and orientate the finished images. REAR SAFETY LATCHES (Fig. 13– Item K1) The Rear Safety Latches lock the Rear Safety Shield into place. REAR SAFETY SHIELD (Fig. 13– Item L1) The Rear Safety Shield protects the operator from harm. REAR TABLE (Fig. 13– Item M1) The Rear Table catches the finished product. FEATURES/ACCESORIES GUIDE Figure 15 Figure 16 Figure 17 BURSTING ROLLERS (Fig. 14– Item N1) When the Bursting Rollers are activated, images are separated. There are 2 speeds to select from on the Main Control Panel. STACKER TRAY LATCHES (Fig. 14– Item O1) The Stacker Tray Latches secures the Stacker Tray to the laminator. FILM TENSION KNOB (Fig. 15– Item P1) The Film Tension Knob allows the operator to adjust the amount of film tension. FILM SLITTER REWINDER TENSION KNOB (Fig. 15– Item Q1) The Film Slitter Rewinder Tension Knob allows the operator to adjust the amount of tension to the Rewinder. MEDIA TABLE (Fig. 16– Item R1) The Media Table provides a working space for the operator. The Media Table is used to store media being used during operation of the laminator. MEDIA TABLE HANDLE (Fig. 16– Item S1) The Media Table Handle allows the operator to pull the Media Table out for use and return to original location. COMPRESSOR OUTPUT HOSE (Fig. 17– Item T1) The Compressor Output Hose supplies the laminator with the necessary PSI to run the laminator. COMPRESSOR PLUG (Fig. 17– Item U1) The Compressor Plug plugs into an independent power source. The Compressor needs 220VAC. See Specs for details on plug configuration. COMPRESSOR AIR REGULATOR (Fig. 17– Item V1) The Compressor Air Regulator allows the operator to adjust the amount of PSI used. COMPRESSOR ON/OFF (Fig. 17– Item W1) The Compressor On/Off allows the operator to turn the Compressor On and off. LOADING FILM & THREADING FILM Locking Pins Figure 1 “O”-RingsFilm Shaft Support BracketFilm Shaft Figure 2 Top IdlerLower IdlerMain Roller Figure 3 Figure 4 DO NOT USE COLORED PRINTS AS SHOWN IN PHOTOS FOR THREADING. STEP 1: • Preheat the laminator to desired temperature. • Turn on the Air Compressor. STEP 2: • Pull the Locking Pins out of the Film Shaft Support Bracket. (Figure 1). • Swing the Film Shaft Support Bracket out and slide the roll of film onto the Film Shaft, over the Core Adaptors. (Figure 2). • Slide the “O”-Ring over the end of the Core Adaptors to keep the rol...