valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
The mitre table features positive click stops at 0°, 15°, 22.5°, 30° and 45° for quick setting of common mitre angles. WARNING. Be sure to tighten the mitre table lock before making a cut. Failure to do so could result in the table moving during the cut and cause serious personal injury. Bevel lock The bevel lock (16) is used to set the blade at the desired bevel angle (fig. G). The mitre saw bevel cuts from 0° to 45° to the left and right. To adjust the bevel angle loosen the bevel lock and pull out the 0° bevel adjuster (18). Adjust the saw arm to the desired bevel angle. WARNING. Be sure to tighten the bevel lock before making a cut. Failure to do so could result in the saw arm moving during the cut and cause serious personal injury.0° Bevel adjuster The bevel adjuster (18) needs to be pulled out before the bevel angle can be adjusted (fig. H). To return the saw arm to the vertical (0° bevel) position move the saw arm to the left and push in the 0° bevel adjuster. Return the saw blade to the vertical position, it will automatically stop at the 0° bevel position. Tighten the bevel lock. Clamp assembly The clamp assembly (10) can be mounted to the fence, either side of the saw blade, to suit the task at hand (fig. I). Use the clamp assembly lock (11) at the back of the fence to secure the clamp assembly in position (fig. J). E H F I G J Spindle lock button The spindle lock button (26) prevents the blade in the saw from rotating (fig. K). Depress and hold the spindle lock button while installing, changing, or removing the blade. Rotating lower blade guard The rotating lower blade guard (12) provides protection from both sides of the blade (fig. L). It retracts over the upper blade guard (9) as the saw is lowered into the workpiece. Dust bag The dust bag (15) fits over the dust extraction port (27). For more efficient operation, empty the dust bag when it is no more than half full. This allows better air flow through the bag (fig. M). Attaching the side bars The side support bars (37) help to support the material when working with long workpieces. There are two location holes (38) for a support bar on either side of the table. Loosen the lock screws (39) with the 6mm hex key. Ensure the side bars are fully inserted before using them to support the workpiece (fig. N). The side support bar locking screws (39) must be tightened to secure the support bars in position (fig. O). Trench depth adjustment In its normal position, the trenching stop (31) permits the saw blade to cut right through a workpiece. When the saw arm is lifted, the trenching stop can be moved to the left so that the trenching depth adjustment screw (30) contacts the stop as the saw arm is lowered. (fig. P). This restricts the cut to a “trench” in the workpiece. The depth of the trench can be adjusted with the trenching depth adjustment screw (30) (fig. Q) and locked in position with the trenching depth lock nut (32) (fig. R). K O L P M Q R N Turning on and off 1. To turn the saw on depress and hold the on/off trigger switch (24) (fig. S). 2. To turn the saw off release the on/off trigger switch (24). Turning on theREDEYE® laser line generator The REDEYE® laser line generator emits 2 intense narrow beams of pure red light to guide you as you cut. It improves operator cutting vision, enables faster set-up, increases accuracy and improves safety. To turn on the laser lines press the laser light on/off switch (2) (fig. T). To turn off the laser press the laser light on/off switch (2) one more time. Setting the table square with the blade 1. Make sure that the electrical plug is removed from the power point. 2. Push the saw arm (5) down to its lowest position and engage the release knob (6) to hold the saw arm in the transport position. 3. Loosen the mitre lock (25) (fig. U). 4. Rotate the table (21) until the pointer is positioned at 0.. 5. Tighten the mitre lock (25). 6. Loosen the bevel lock (16) and set the saw arm (5) at 0. bevel (the blade at 90. to the mitre table). Tighten the bevel lock (16) (fig. V). 7. Place a set square against the table (21) and the flat part of the blade. (fig. W) Note. Make sure that the square contacts the flat part of the saw blade, not the teeth. 8. Rotate the blade by hand and check the blade-to- table alignment at several points. 9. The edge of the set square and the saw blade should be parallel. 10. If the saw blade angles away from the set square, adjust as follows. 11. Use a 13mm wrench or adjustable wrench to loosen the lock nut securing the 0° bevel adjustment screw (35) (fig. X). Also, loosen the bevel lock (16). S V W T 90° X U 12. Adjust the 0° bevel adjustment screw (35) with the 6mm hex key to bring the saw blade into alignment with the square (fig. Y). 13. Loosen the 2 Phillips head screws holding the pointer of the bevel scale (17) and adjust the position of the pointer so that it accurately indicates zero on the scale (fig. Z). Retighten the screw. 14. Retighten the bevel lock (16) and the lock nut ...
Questo manuale è adatto anche per i modelli :Jig Saw e - REDEYE DB250SMS (710.76 kb)