valutazioni - , GPA:
(
)
)
Produttore : Global Machinery Company
File Size : 484.23 kb
File Nome : 4393c8fb-a054-b1f4-4150-96824e191d7c.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Disc guard 4. Front spark shield 5. Spark shield locking knob 6. Cut off disc 7. Spindle lock 8. Rear spark shield 9. Base 10. Rubber foot 11. Vice lock release lever 12. Vice handle 13. Vice 14. Fence 15. Carry handle 16. Lock down knob 17. Depth stop 18. 8mm Hex key 19. 5mm Hex key 1 18 19 3 16 2 15 4 5 7 6 17 8 14 13 9 11 16 12 10 Overview The cut off saw is used for cutting steel such as pipe, box section, rectangular, angle iron and steel bars. The saw can cut at angles from 0° to 45° left and right, it features a two position fence that permits an extended cutting range. The quick release vice allows fast adjustment whilst the lock-off button prevents accidental operation. Attaching the rubber feet 1. Tilt the saw onto its side. 2. Take the rubber feet and insert 1 rubber foot into the matching slots on the base of the saw. 3. Ensure the rubber feet are fully inserted into the slots. 4. Repeat for the other side and place the chop saw back on its base. Attaching the rear spark shield 1. Loosen and remove the hex bolt, flat washer and star washer at the back of the saw using the 5mm hex key supplied. 2. Place the flat washer over the hex bolt and then fit the hex bolt through the spark deflector, place the star washer over the hex bolt so it is in between the spark deflector and the cut off saw. Place the spark shield in the correct position and tighten the hex bolt. 3. Tighten the hex bolt to secure the spark shield in position. Adjusting the vice The vice can be adjusted quickly by loosening the vice lock release lever and pushing forward. 1. Place your workpiece in between the fence and vice. 2. Lift the vice lock release lever and push the vice forward. 3. Once the vice hits the workpiece move the vice lock release lever back down. 4. Rotate the vice handle in a clockwise direction to secure the workpiece in position. 5. To remove an object from the vice, rotate the vice handle in an anti-clockwise direction until the vice jaws are loose. The work piece can now be removed, the vice lock release lever can also be lifted to slide the vice back quickly. Note. The vice lock release lever cannot be lifted until the vice jaws are loose. Adjusting the cutting angle 1. To change the cutting angle loosen the 2 hex screws securing the fence using the 8mm hex key supplied. 2. Move the rear fence to the desired angle using the scale as a guide. 3. Tighten the 2 hex bolts to secure the fence in position. CAUTION. Only perform miter cuts when the fence is set at the most forward position. Note. For accurate cuts, test the cutting angle on some similar scrap material and adjust the angle to suit your requirements. The scale is only a guide. Adjusting the fence 1. The original spacing between the vice and the fence is 175mm. 2. When cutting wider materials the rear fence will need to be adjusted to the rear most position. When cutting narrow work pieces the fence should be positioned in the most forward position. 3. To adjust the fence loosen and remove the two hex bolts securing the fence using the 8mm hex key supplied. 4. Move the fence backwards or forwards to one of the other two fixing positions. 5.Tighten the 2 hex bolts to secure the fence in position. CAUTION. Narrow work pieces may not be secured safely when using the two wider interval settings. Turning on and off 1. Plug the cordset into the mains socket. 2. Push the lock-off button and pull the trigger to start the tool. 3. To stop the tool release the trigger switch 4. When you release the trigger switch, the machine turns off and the lock-off button re-engages to prevent accidental operation. Warning. The cutting disc will continue to run down for a short period of time after the trigger swich has been released. Replacing a cut off disc CAUTION. Always ensure that the saw is switched off and unplugged from the power supply before installing or removing a disc. 1. Loosen and remove the spark shield locking knob. 2. Swing the front spark shield downwards and pull out from the upper disc guard to reveal the cutting disc bolt and flange. 3. Push the spindle lock lever to the right and rotate the disc until the spindle lock engages. 4. Whilst holding the spindle lock lever use the 8mm hex key supplied to remove the disc bolt. Note that the bolt unscrews in an anti-clockwise direction. 5. Remove the disc lock bolt, washer, outer flange, blotter and cut off disc. 6. Clean any grinding dust from the inner flange and, after checking that it is in good condition, mount a new disc between two paper blotters. The rear blotter should be mounted onto the inner flange and the front blotter is the printed surface on the front of the disc. 7. Replace the outer flange, washer and lock bolt. Tighten the bolt in a clockwise direction. 8. Turn the new disc by hand, ensuring that it rotates fully and does not wobble unduly. 9. Replace the front spark shield by locating the centre pivot section of the spark shield into the raised centre section of the upper disc guard. Not...