valutazioni - 6, GPA: 3.8
(
)
)
|
Facilità d'uso
The nozzle is attached to a fully adjustable stand that permits an endless combination of nozzle positions. Tools Needed: Phillips Screwdriver AWARNING Be sure to read the entire instruction sheet before beginning the construction of this product. Follow every step and use the recommended tools and supplies. Also, read the instruction manuals for any tools you are using to complete this project. Be certain that the tools used for this installation are intended for the task which will be performed. Failure to do this could result in serious personal injury. Awarning Wear safety glasses during the entire assembly process. Failure to comply may result in serious personal injury. Assembly: 1. Thread the (3) M8-1.25 x 25 Feet into the bottoms of the (3) Legs. 2. Using the (12) M6-1 x 8 Phillips Head Screws, 6mm Lock Washers, and 6mm Flat Washers, attach the (3) Legs to the Main Tube Body. Be sure the Lock Washers are between the Flat Washers and the Phillips Screw heads when tightened down. 3. Thread the M8-1.25 x 20 Lock Knob into the threaded hole on the side of the Main Tube Body. 4. Attach the Fixed Support to the top end of the Silver Main Tube Body using (2) M6-1.0 x 20 Phillips Head Screws. 5. Thread the M10-1.5 Hex Nut onto the end of the M10-1.5 x 15 Lock Knob. Place the end of the Lock Knob and Hex Bolt assembly through the slot on the Vacuum Tube. After the knob has been slide through the slot, place the 10mm Flat Washer on the threaded end of the Knob. 6. Carefully thread the Knob into the threaded hole in the Fixed Support. Be sure the Flat Washer is between the Fixed Support and the Vacuum Tube. This Washer acts as a pivot point when adjusting the Nozzle position. Tighten the Knob until the Vacuum Tube remains stationary. 7. Slide the Nozzle into the end of the Vacuum Tube. The Nozzle can be rotated 360° within the Vacuum Tube. Thread the M6-1 x 15 Lock Knob into the threaded hole on the top of the Vacuum Tube. This Knob locks the Nozzle into position. 8. You are now ready to enjoy dust collection in just about any location of your shop. If the Stand is unlevel, thread the Feet in and out until proper adjustment is achieved. NOTICE The performance of your Model D2267 will only be as good as the performance of your dust collector. Regular maintenance of your dust collector will ensure maximum performance from your Model D2267, within the limitations of your dust collector. If You Need Assistance: We hope you will find that your Shop Fox® Model D2267 is easily assembled and put to use. Should you have any questions about this product, please contact the dealer where you purchased it, or you can contact the Woodstock International Technical Department at 1-360-734-3482, Monday through Friday, between the hours of 7:00 am to 5:00 pm PST or e-mail us at: tech-support@woodstockint.com REF PART # DESCRIPTION 1 XD2267001 VACUUM TUBE 2 XD2267002 NOZZLE 3A XD2267003A LOCK KNOB M6-1 X 15 4 XD2267004 FIXED SUPPORT 5A XD2267005A LOCK KNOB M10-1.5 X 15 6A XPW04M FLAT WASHER 10MM 7A XPS26M PHLP HD SCR M6-1 X 20 8A XD2267008A MAIN TUBE BODY 9A XD2267009A LOCK KNOB M8-1.25 X 20 10 XD2267010 SILVER MAIN TUBE BODY 11A XPN02M HEX NUT M10-1.5 12A XPS03M PHLP HD SCR M6-1 X 8 13A XD2267013A LEG 14A XPLW03M LOCK WASHER 6MM 15A XPW03M FLAT WASHER 6MM 16A XD2267016A FOOT M8-1.25 X 25 10 9A 8A COPYRIGHT © APRIL 2002 BY WOODSTOCK INTERNATIONAL, INC. REVISED SEPTEMBER, 2010 (TR) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. 433402922...