valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Do not support the work with the narrow sides as this is an unsteady arrangement. If the sheet or board to be cut is too large for a table or work bench, use the supporting two-by-fours on the floor and secure. FIG. 11 FIG. 12 WRONG RIGHT RIP CUTS The combination blade provided with your saw is for both cross cuts and rip cuts. Ripping is cutting lengthwise with the grain of the wood. Rip cuts are easy to do with a rip fence (Fig. 13). To attach fence, insert fence through slots RIP BOARD GUIDE When rip cutting large sheets, the rip fence may not allow the desired width of cut. Clamp or nail a straight piece of 1" (25 mm) lumber to the sheet as a guide (Fig. 14). Use the right side of the foot against the board guide. -12- in foot to desired width as shown and secure with the knob. FIG. 13 FIG. 14 RIP FENCE KNOB DESIRED WIDTH OF CUT DESIRED LINE OF CUT RIP BOARD GUIDE BM 2610914527 3/03 3/18/03 10:47 AM Page 13 RELEASING AND INSERTING BATTERY PACK Release battery pack from tool by pressing pack. To insert battery, align battery and on both sides of the battery release tabs and slide battery pack into tool until it locks into pull downwards. Before inserting battery position. Do not force. pack, remove protective cap from battery CHARGING BATTERY PACK (1 HOUR CHARGER) Plug charger cord into your standard power outlet. Before inserting battery pack, remove protective cap, then insert battery pack into charger (Fig. 15). The charger’s green indicator will begin to “BLINK”. This indicates that the battery is receiving a fast charge. Fast-charging will automatically stop when the battery pack is fully charged. When the indicator light stops “BLINKING” (and becomes a steady green light) fast charging is complete. When you begin the charging process of the battery pack, a steady green light could also mean the battery pack is too hot or too cold. BATTERY PACK INDICATOR LIGHT CHARGER PROTECTIVE CAP BATTERY PACK RELEASE TABS The purpose of the light is to indicate that the battery pack is fast-charging. It does not indicate the exact point of full charge. The light will stop blinking in less time if the battery pack was not completely discharged. When the battery pack is fully charged, unplug the charger (unless you're charging another battery pack) and slip the battery pack back into the tool handle (Fig.15). To prevent fire or injury when batteries are not in tool or charger, always place protective cap onto end of battery pack. FIG. 15 IMPORTANT CHARGING NOTES 1. The battery pack accepts only about 80% 2. The charger was designed to fast charge of its maximum capacity with its first few the battery only when the battery charge cycles. However, after the first few temperature is between 40°F (4°C) and 105°F charge cycles, the battery will charge to full (41°C). capacity. -13 BM 2610914527 3/03 3/18/03 10:47 AM Page 14 3. A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced. 4. If you anticipate long periods (i.e. a month or more) of non-use of your tool, it is best to run your tool down until it is fully discharged before storing your battery pack. After a long period of storage, the capacity at first recharge will be lower. Normal capacity will be restored in two or three charge/discharge cycles. Remember to unplug charger during storage period. 5. If battery does not charge properly: a. Check for voltage at outlet by plugging in some other electrical device. Maintenance Service NO USER SERVICEABLE PARTS INSIDE. Preventive ! WARNING maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Bosch Factory Service Center or Authorized Bosch Service Station. SERVICEMEN: Disconnect tool and/or charger from power source before servicing. BATTERIES Be alert for battery packs that are nearing their end of life. Battery packs typically last from 500 to 1000 charges. If you notice decreased tool performance or significantly shorter running time between charges then it is time to replace the battery pack. Failure to do so can cause the tool to operate improperly or damage the charger. Long term battery storage should be in the discharged state. Battery packs last longer and re-charge better when they are stored discharged. Remember to fully recharge battery packs before using after prolonged storage. TOOL LUBRICATION Your Bosch tool has been properly lubricated and is ready for use. D.C. MOTORS The motor in your tool has been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend it be examined every six months. Only a genuine Bosch replacement motor specially designed for your tool should be used. BEARINGS Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating and motor failure. Cleaning ! ...
Questo manuale è adatto anche per i modelli :Jig Saw e - 1660 (665.17 kb)