valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
The blade may be inserted with the teeth facing down or up. 3. To remove the blade, rotate the locking collar counter-clockwise and the blade will automatically eject from the LockJaw™ blade holder and lock the collar in the open position. !WARNING Make sure that the front end of the blade extends through the footplate for the entire stroke length. Do not use specialty blades that are very short or those with a significant cant. Blade must not contact footplate. A blade which is too short or canted could jam inside the foot and snap. FIG. 3 Open Position LOCKING COLLAR Operating Instructions INSTALLING POWER CORD Recommended: !WARNING To reduce the risk of injury and tool damage, do not use extension cords that have receptacles bodies with sides that taper towards the end of the receptacle. Use of this extension cord type may result in an intermittent electrical connection and cause arcing. Only use extension cords that are UL Listed. For best performance, use BOSCH extension cords. !WARNING DIRECT CORD CONNECT SYSTEM HAS BEEN CONFIGURED TO BE USED WITH 12AWG SJ CORD, MAXIMUM LENGTH OF 50 FEET. INSPECT THE CORD, DO NOT USE IF DAMAGED. -7 1. Loop cord as shown in figure 4. 3. Push end of plug through spring clip and into female outlet in handle as shown in figure 6. FIG. 4 2. Insert looped end of cord through slot in handle and loop cord into channel provided in handle as shown figure. 5). SPRING CLIP FIG. 6 SPRING CLIP FIG. 5 ATTENTION: before inserting plug into handle, always make sure you leave enough cord at plug end to avoid tension on plug when inserted into tool. VARIABLE SPEED CONTROLLED TRIGGER SWITCH Your tool is equipped with a variable speed controlled trigger switch. The tool can be turned "ON" or "OFF" by squeezing or releasing the trigger. The blade plunger stroke rate can be adjusted from the minimum to maximum nameplate stroke rate by the pressure you apply to the trigger. Apply more pressure to increase the speed and release pressure to decrease speed (Fig. 1). DUAL SPEED SELECTOR SWITCH Your tool is equipped with two separate gear ranges, low gear and high gear. Low gear ATTENTION: Insure your cord is completely inserted into the handle and that it is fully seated against the Direct Connect end plug. 4 To remove plug from tool, simply remove from outlet and pull away from spring clip. NOTE: If the spring clip does not securely hold the plug it may be necessary to lightly squeeze the clip together with a pliers. If you have any questions or experience a problem with your Direct Connect system, contact us at 1-877-BOSCH99 or visit provides slower cutting speeds for cutting hard materials such as metals or thin sheet metals. High gear provides faster speeds for cutting soft materials such as wood, plastics, etc. and when fast cutting is more important than a clean cut. To change speeds slide switch, to the high or low position (Fig. 1). JOB-LIGHT Your tool is also equipped with a Job-light for better visibility during operation (Fig. 1). When the tool is plugged in, the light will turn on automatically and stay on until the plug has been removed from the power source. FOOTPLATE ADJUSTMENT The footplate tilts in order to keep as much of its surface in contact with the work surface Fig. 7 (a). The footplate assembly can also be locked into one of three projection positions to optimize blade life and/or to reduce blade protrusion beyond the end of the footplate, such as when cutting into large diameter pipe or into walls. To adjust the footplate position, simply push the footplate release button and move the footplate into the desired position. The locking mechanism is spring-loaded to lock into one of the 3 positions on the footplate assembly. If the footplate is pulled out so far that a notch shows at the other end of the shaft, the footplate assembly is extended too far out, and must be retracted to the one of the 3 positions Fig. 7 (b). -8 !WARNING !WARNING Do not push the footplate !WARNING To reduce the risk of injury, release button while sawing. be sure the blade extends It will cause the footplate to release from the desired settings and you may lose control and be injured. FIG. 7 FIG. 8 (a) (b) SAW HOOK Your tool is equipped with a convenient saw hook for hanging your tool. To use, simply lift up hook until it snaps into the open position (Fig. 9). When not in use, always lower hook until it snaps into the closed position. beyond the footplate and all the way through the workpiece throughout the stroke. Blades may shatter if the blade hits the footplate or hits the work at an angle that is nearly head- on (Fig. 8). FIG. 9 SAW HOOK Using the Saw 1. Securely clamp the work. 2. Mark the line of cut and grasp the tool with one hand on the handle and the other placed on the insulated rubber boot over the front housing. !WARNING Always hold the saw by the insulated boot on the front housing. If you saw into a blind area where live wiring exists, you may be shocked or ele...