valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
Besides the instructions, data sheet, circuit requirements, parts, and wiring diagram in this insert, the content in the Model G0566 owner's manual is the same for both machines. Before operating your new machine, you Must read and understand this insert and the entire Model G0566 manual to reduce the risk of injury from improper use or setup. If you have any further questions about this manual insert or the differences between the Model G0531B/ G0566B and the Model G0566, contact our Technical Support at (570) 546-9663 or email techsupport@ grizzly.com. Machine Inventory After all the parts have been removed from the crate, you should have the following items: crate contents (Figure 1): A. Bandsaw (not shown) .... B. Miter Gauge................... c. Fence............................. D. Resaw Fence ................ E. guide post Handwheel.. Qty Hardware and Tools (not shown) hex Wrench 5mm...................................... hex Wrench 6mm...................................... open End Wrench 10 x 13........................ open end Wrench 17 x 19........................ Lifting rings............................................... resaw Fence lock handle M8-1.25 x 44 (Fence)...................................................... Moving plate M8-1.25 (Fence).................. Flat Washer 8mm (Fence) ........................ Qty .... 1 .... 1 .... 1 .... 1 .....2 Figure 1. G0531B/G0566B inventory. installing fence components and hardware Needed: Fence Assembly ........................................ resaw Fence Assembly ............................ resaw Fence lock handle M8-1.25 x 44 . Moving plate M8-1.25............................... Flat Washer 8mm...................................... Qty To install the fence: 1. remove the cap screw, knobs, and washers that hold the rail onto the table, then remove the rail. 2. Flip the rail over and reinstall with the fast-ners removed in step 1. install the fence handle on the fence, if it is not already installed. copyright © june, 2008 by grizzly industrial, inc. warning: no portion of this manual may be reproduced in any shape or form without the written approval of grizzly industrial, inc. #BL10789 printed IN TAIWAN 4. Tighten the hex nut on the fence handle against the fence pivot block (Figure 2). Figure 2. Fence handle components. 5. Install the resaw fence lock handle (with the 8mm washer and moving plate) onto the fence, then slide the resaw fence over the moving plate as shown in Figure 3. Note: Leave the moving plate and lock handle loose enough to slide on the resaw fence. Figure 3. Example of attaching resaw fence to standard fence. 6. Tighten the resaw lock handle. Test Run 1. Follow Steps 1-3 in the G0566 Manual on page 24. 2. Verify that the machine is operating correctly by turning the switch disabling key (Figure 4) to "1" and turning the machine ON. —When operating correctly, the machine runs smoothly with little or no vibration or rubbing noises. —Investigate and correct strange or unusual noises or vibrations before operating the machine further. Always disconnect the machine from power when investigating or correcting potential problems. Figure 4. G0531B switch disabling key and oN/ oFF switch. 3. Press the OFF button to stop the machine. 4. WITHOuT resetting the OFF button, press the ON button. The machine should not start. —If the machine does not start, the OFF button safety feature is working correctly. 7. pull the fence handle up and place the fence assembly on the rail. 8. push the fence handle down to lock the fence assembly in place. —If the machine does start (with the stop button pushed in), immediately disconnect power to the machine. The OFF button safety feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech support for help. * Model G0531 B/G0566B 5. Twist the OFF button clockwise so it pops out. When the OFF button pops out, the switch is reset and ready for operation (see Figure 5). 6. Turn the switch disabling key to "0", as shown in Figure 4. 7. Try to turn the machine ON. —If the bandsaw does not start, the switch disabling feature is working as designed. The Test Run is complete. —If the bandsaw starts, immediately disconnect power. The switch disabling feature is not working correctly. This safety feature must work properly before proceeding with regular operations. Call Tech support for help. Motor Brake The motor brake is activated automatically when the OFF button is pushed, quickly bringing the blade to a stop. Aligning Fence To ensure cutting accuracy when the fence is first installed, the fence should be aligned with the miter slot. To align the fence parallel with the miter slot: 1. disconnect bandsaw FROM POWER! 2. Make sure the miter slot is aligned with the bandsaw blade (see G0566 Manual page 22, Table Alignment). 3. Mount the fence next to the miter slot, then loos...
Questo manuale è adatto anche per i modelli :Jig Saw e - G0566B (2.79 mb)