valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
3. Have cord replaced. Remedy 1. Replace with adequate size cord. 2. Feed stock more slowly. 3. Clean or replace blade. 4. Contact your electric company. Remedy 1. Tighten all mounting hardware. 2. Reposition on flat level surface. 3. Replace belt. 4. Adjust belt tension by moving motor. 5. Tighten all mounting hardware. Remedy 1. Replace with adequate size cord. 2. Contact your electric company. Remedy 1. Adjust blade tension. 2. Check and adjust blade guides. 3. Adjust blade support bearing. 4. Check and adjust blade tracking. 5. Replace the blade. 6. Replace tires. 7. Change to a narrower blade. 8. Replace blade. 9. Set upper blade guide within 1/8" of workpiece. 10. Turn off machine when not performing cutting operation. (continued on next page) 19 TROUBLESHOOTING GUIDE (CONTINUED) Trouble: BLADE WILLNOT TRACK. Probable Cause Remedy 1. Blade too loose 1. Adjust tension 2. Upper wheel not properly adjusted. 2. Adjust upper wheel. 3. Improperly adjusted blade support bearing. 3. Adjust blade support bearing. Trouble: CUT DOES NOT AGREE WITH SETTING ON THE TILT SCALE. Probable Cause Remedy 1. Pointer out of adjustment 1. Adjust pointer. Trouble: BLADE WILLNOT STAYON WHEEL. Probable Cause Remedy 1. Blade not tensioned properly. 1. Adjust blade tension. 2. Blade guides improperly adjusted. 2. Check and adjust blade guides. 3. Blade support bearing improperly adjusted. 3. Adjust blade support bearing. 4. Blade wheel not tracking properly. 4. Check and adjust blade tracking. 5. Bad weld on blade. 5. Replace the blade. 6. Worn tires. 6. Replace tires. Trouble: BAND SAW MAKES UNSATISFACTORYCUTS. Probable Cause Remedy 1. Blade not tensioned properly. 1. Adjust blade tension. 2. Blade guides improperly adjusted. 2. Check and adjust blade guides. 3. Blade support bearing improperly set. 3. Adjust blade support bearing. 4. Blade wheel not tracking properly. 4. Check and adjust blade tracking. 5. Bad weld on blade. 5. Replace the blade. 6. Worn tires. 6. Replace tires. 7. Incorrect blade for work being done. 7. Change the blade. 8. Dull blade or insufficient set. 8. Replace blade. 9. Upper blade guide set too high. 9. Set upper blade guide within 1/8" of work piece. 10. Continuous running of machine when not actually 10. Turn off machine when not performing cutting cutting. operation. 20 BAND SAW BLADES A band saw blade is a delicate piece of steel that is subjected to tremendous strain. You can obtain long use from a band saw blade if you use it properly. Be sure you use blades of the proper thickness, width and temper for the various types of material and cuts. Always use the widest blade possible. Use narrow blades only for sawing small, abrupt curves and for fine, delicate work. This will save blades and will produce better cuts. For cutting wood and similar materials, Shopmaster offers blades in widths of 1/8", 1/4", and 3/8". Any one of a number of conditions may cause a band saw blade to break. Blade breakage is, in some cases, unavoidable, being the natural result of the peculiar stresses to which blades are subjected. Blades will brake often due to avoidable causes, such as the lack of care to the blade or the blade not being properly adjusted to the band saw. The most common causes of blade breakage are: (1) faulty alignments and adjustments of the guides. (2) forcing or twisting a wide blade around a curve of short radius. (3) feeding the work piece to fast into the blade. (4) dullness of the teeth, or absence of sufficient set. (5) excessive tensioning of the blade. (6) top guide set too high above the work piece being cut. (7) using a blade with a lumpy or improperly finished braze or weld. (8) continuous running of the saw blade when the blade is not in use. Use blades that are 59-1/2" in length on this machine. Always use a sharp blade. Keep it free from gum and pitch. Clean frequently with a stiff fiber brush. Narrow blades are used for cutting small circles or curves while the wider blades are best suited for straight cutting such as ripping. A new blade, in most cases, will perform better and last longer than a re-sharpened blade. Insure that the blade guides are adjusted properly. Do not force or twist the blade around a curve or a very short radius. Feed the workpiece through the blade at a consistent rate, allow the blade to do the cutting – do not feed the work piece too fast. Do not apply excessive tension to the blade. The tension is only necessary to drive the blade without slipping on the wheels. Narrow blades require less tension than wider blades. 21 NOTES 22 NOTES 23 MAINTENANCE MAINTENANCE KEEP MACHINE CLEAN If using compressed air to clean out sawdust wear ANSI Z87.1 safety glasses. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable · Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site www.deltam...
Questo manuale è adatto anche per i modelli :Jig Saw e - ShopMaster SM400 (662.55 kb)