valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
b. Align the arrow on the housing wdith the line on the shoe Fig. 7. c. Rotate the shoe to the desired angle. After setting the shoe, tighten it by returning the shoe lever to its oringinal position. NOTE: The shoe will be difficult to bevel at first. Ensure the shoe lever is up and the two arrows shown are aligned. Gently rock the shoe from side to side to loosen. At 0°, the shoe may slide back to allow for cutting in tight work areas. Lift the shoe lever, slide the shoe back and depress the lever to lock. If necessary tighten the shoe lever with the screw (B). Attaching Blades (Fig. 8) UNPLUG TOOL. Insert any universal or “T” shank jig saw blade inthe the chuck. Make sure the back edge of the blade fits into the support roller. Lift knob approximately 1/4” as shown. Maintain tension on the knob and rotate it clockwise several revolutions until it clicks or gets tight. Do not over tighten. Only moderate pressure is necessary. To remove blades, lift and turn knob counterclockwise 2 or 3 revolutions. For “T” shank blades, insert blade to the shoulder of the shank. Pocket Cutting (Fig. 9) A pocket cut is an easy method of making an inside cut. The saw can be inserted directly into a panel or board without first drilling a lead or pilot hole. In pocket cutting measure the surface to be cut and mark clearly with a pencil. Be sure the shoe is extended forward. Next tip the saw forward until the front end of the shoe sits firmly on the work surface and the blade clears the work through its full stroke. Switch the tool on and allow it to attain maximum speed. Grip the saw firmly and lower the back edge of tool slowly until the blade reaches its complete depth. Hold the shoe flat against the wood and begin cutting. Do not remove blade from cut while it is still moving. Blade must come to a complete stop. Wood Cutting Be sure board is firmly positioned. Don’t attempt to turn on when blade is against material to be cut. This could stall the motor. Place front of shoe on material to be cut and hold jig saw shoe firmly against the wood while cutting. Don’t force the tool; let the blade cut at its own speed. Whenever possible, clamp or support work close to the line of cut; when the cut is completed, shut off power, let blade come to a complete stop and then lay the saw aside before loosening the work. Use the higher speed setting for cutting wood. Metal Cutting In cutting thin gauge sheet metals, it is best to clamp wood or plywood to the bottom of sheet metal; this will insure a clean cut without the danger of vibration or tearing of metal. Always remember to use a finer blade for ferrous metals (for those that have a high iron content); and use a coarser blade for non-ferrous metals (those that do not have an iron content). Use a high speed setting for cutting soft metals (aluminum, copper, brass, mild steel, gallvanized. pipe, conduit sheet metal, etc.). Use lower speed to cut plastics, tile, Formica, hard metals, cast iron. Lubrication It is recommended that, at least once a year, you take or send the tool to a service center for a thorough cleaning, inspection and lubrication of the gear case. Accessories Recommended accessories for use with your tool are available at extra cost from your local service center. CAUTION: The use of any non-recommended accessory may be hazardous. If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258). Repairs To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. Three Year Limited Warranty DEWALT will repair, without charge, any defects due to faulty materials or workmanship for three years from the date of purchase. This warranty does not cover part failure due to normal wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit or call 1-800-4-DEWALT (1-800-433-9258). This warranty does not apply to accessories or damage caused where repairs have been made or attempted by others. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces. In addition to the warranty, DEWALT tools are covered by our: 1 YEAR FREE SERVICE DEWALT will maintain the tool and replace worn parts caused by normal use, for free, any time during the first year after purchase. 90 DAY MONEY BACK GUARANTEE If you are not completely satisfied with the performance of your DEWALT Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked. FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-4-DEWALT for a free replacement. POUR TOUTE QUESTION OU...
Questo manuale è adatto anche per i modelli :Jig Saw e - DW323 (249.23 kb)