valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
MAKE WORKSHOP KID PROOF 6. with padlocks, master switches, or by removing starter keys. DON’T FORCE TOOL. It will do the 7. job better and safer at the rate for which it was designed. USE RIGHT TOOL. Don’t force tool 8. or attachment to do a job for which it was not designed. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS (120 VOLT) NAMEPLATE AMPERES (at full load) EXTENSION CORD LENGTH 25’ 50’ 100’ 150’ 0 – 6 18 16 16 14 6.1 – 10 18 16 14 12 10.1 – 12 16 16 14 12 12.1 – 16 14 12 Do not use. TABLE A USE PROPER EXTENSION CORD. 9. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table A shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. WEAR PROPER APPAREL. Do not 10. wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to contain long hair. ALWAYS USE SAFETY GLASSES. 11. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. SECURE WORK. Use clamps or a 12. vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool. DON’T OVERREACH. Keep proper 13. footing and balance at all times. MAINTAIN TOOLS WITH CARE. 14. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. DISCONNECT TOOLS before ser15. vicing; when changing accessories, such as blades, bits, cutters, and the like. REDUCE THE RISK OF UNINTEN16. TIONAL STARTING. Make sure switch is in off position before plugging in. USE RECOMMENDED ACCESSO17. RIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons. NEVER STAND ON TOOL. Serious 18. injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. CHECK DAMAGED PARTS. Before 19. further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. DIRECTION OF FEED. Feed work 20. into a blade or cutter against the direction of rotation of the blade or cutter only. NEVER LEAVE TOOL RUNNING 21. UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop. Grounding Instructions To prevent electric shock and death from incorrect grounding wire connection Read and follow these instructions: 110-120 V~ Grounded Tools: Tools with Three Prong Plugs In the event of a malfunction or 1. breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment- grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not modify the plug provided – if it 2. will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equip3. ment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment- grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal. Check with a qualified electrician or 4. service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Use only 3-wire extension cords that 5. have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. Repair or replace damaged or worn 6. cord immediately. 125 V~ 3-Prong Plug and Outlet(for up to 125 V~ and up to 15 A) Grounding Pin This tool is intended for use on a cir7. cuit that has an outlet that looks like the one illustrated above in 125 V~ 3-Prong Plug and Outlet. The tool has a grounding plug that looks like the plug illustrated above in 125 V~ 3-Prong Plug and Outlet. The outlet must be properly installed 8. and grounded in accordance with all codes and ordinances. Do not use an adapter to connect this 9. tool to a different outlet. Cutoff Saw Safety Warnings CHECK WHEEL PRIOR TO USE. 1. Check for any cracks or other flaws in the wheel that would indicate structural damage. If any are det...