valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
For a shallower cut, slide the Adjustable Shoe Plate further away from the Guard Plate. (See Figure C.) 3. Then, retighten the two Hex Screws (58). (See Figure C.) BOTTOM VIEW HEX SCREW GUARD PLATE (2) ADJUSTABLE SHOE PLATE FIGURE C (58) (1) Operating Instructions: 1. The Reciprocating Saw is equipped with a Trigger Lock mechanism. To operate the tool for extended periods of time squeeze and hold the Trigger (37), then press the Trigger Lock. To unlock the Trigger Lock mechanism, squeeze and release the Trigger once. (See Figure B.) 2. Before plugging the Reciprocating Saw into its 120 Volt, grounded, electrical outlet check to make sure the Trigger (37) is not locked in its “ON” position. Press and release the Trigger once to make sure the Trigger is unlocked and “OFF”. (See Figure B.) 3. Plug the Reciprocating Saw into its 120 Volt, grounded, electrical outlet. 4. NOTE: The Reciprocating Saw has a variable speed setting from 0 to 2300 SPM (strokes per minute). When cutting softer materials, use a faster speed. When cutting hardermaterials, use a slowerspeed. (See Figure B.) 5. Hold the Reciprocating Saw firmly with both hands, then squeeze the Trigger (37) to start the Saw. NOTE: Do not start the Reciprocating Saw if the Saw Blade (59, 60) is in contact with anything before operation. If necessary, lift the Reciprocating Saw to free the Saw Blade before squeezing the Trigger. (See Figure B.) 6. If operating the Reciprocating Saw for an extended period of time, you may wish to lock the Trigger (37) in position as described in Step #1). (See Figure B.) 7. With the Reciprocating Saw “ON”, place the Saw Blade (59, 60) against the material to be cut. Press down slightly on the Reciprocating Saw to help it cut. (See Figure B.) SKU 4095 For technical questions, please call 1-800-444-3353. PAGE 11 8. Once the cutting procedure is completed, release pressure on the Trigger (37) to stop the Reciprocating Saw. If the Trigger Lock was used, squeeze and release the Trigger once to stop the Saw. Then, unplug the Saw from its electrical outlet. (See Figure B.) INSPECTION, MAINTENANCE, AND CLEANING 1. Make sure the Trigger of the Reciprocating Saw is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing WARNING! any inspection, maintenance, or cleaning procedures. 2. BEFORE EACH USE, inspect the general condition of the Reciprocating Saw. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, cracked or broken Saw Blades, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. 3. TO CLEAN, use a clean cloth or vacuum to remove all dust and debris from the Reciprocating Saw. Do not use any solvents. THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND AS- SEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TOTHE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,THE MANUFACTURER AND/ OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO. PLEASE READ THE FOLLOWING CAREFULLY SKU 4095 For technical questions, please call 1-800-444-3353. PAGE 12 PARTS LIST Part Description Part Description 1 Adjustable Shoe Plate 37 Trigger 2 Guard Plate 38 Right Body 3 Rubber Sleeve 39 ** Washer 4 Screw 40 ** Retaining Washer 5 Cover 41 Screw 6A Hex Screw 42 Power Cord Support 6B Hex Screw 43 Screw 7 Blade Holder 44 Power Cord 8 Felt Retainer 44B Cord Guard 8B Felt Pad 45 Racing Plate 9 Shock Absorber 46 ** Inducer 10 Small Cover Sheet A 47 Screw 11 Screw 48 Screw 12 Retaining Washer 49 ** Screw 14 Reciprocating Bar 50 Wingshield Ring 15 Sliding Bearing 51 * Ball Bearing (80018) 15B Felt Pad 52 * Rotor 18 Left Body 53 * Screw 19 Speed Control 54 * Bearing Cover 20 Small Cover Sheet B 55 * Ball Bearing (80200) 23 Large Washer 57 ** Stator 24 Roller Bearing (HKH1216) 58 Screw 26 Roller 59 Wood Saw Blade (not shown) 27 Roller Shaft 60 Metal Saw Blade (not shown) 28 Gear Wheel 61 Replacement Brushes (not shown) 29 Washer 62 4MM Hex Key (not shown) 30 Center Column 63 Rotor Assembly (Includes 51-56) 31 Machine Head * Only available as part of Rotor Assy. (63) 32 Carbon Brush 33 Brush Holder 64 Stator/Lift Body Assembly (Includes 18, 46, 39, 40, 49, 57)34 Screw 35 Washer ** Only available as part of Stator/Lift Body Assy. (64)36 Screw Nut NOTE: Some parts are listed and shown for illustration purposes only, and are not available indi...