valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
b. Slightly loosen the two Hex Screws (16) on the Blade Guide Assembly (38). c. Insert the Saw Blade (59, 60) upward into the Blade Guide Assembly (38), and retighten the two Hex Screws (16) to secure the Saw Blade in place. Make sure the teeth of the Saw Blade face forward as shown. d. Then, lower the Blade Guard (9) to its original position. 2. LASER GUIDE BATTERY INSTALLATION: a. Remove the Battery Compartment Lid (57) on the front of the Jigsaw to expose the Battery Compartment. b. Install two “AAA” size Batteries (not included) in the Compartment, making sure to match the polarity of contacts as indicated in the Compartment. c. Then, reattach the Battery Compartment Lid. 3. BEVEL ADJUSTMENT: The Base Plate (41) can be tilted to cut any angle between 0 and 45° right and left. a. Loosen the Hex Screw (16). Rotate the Base Plate right or left to the desired angle of cut. b. Then, retighten the Hex Screw (16). Work Piece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working. 3. Secure loose work pieces using a vise or clamps (not included) to prevent movement while working. 4. There must not be objects, such as utility lines, nearby that will present a hazard while working. General Operating Instructions 1. Squeeze and release the Trigger to put it in its off position. If necessary, make adjustments to the Speed Control Dial (20) and Cutting Mode Selector (46). Also if necessary, adjust the Base Plate (41) for the desired bevel of cut. 2. Then, plug the Power Cord (43) into the nearest 120 volt, grounded, electrical outlet. 3. Position the Saw Blade (59, 60) of the Jigsaw about 1/2” from the beginning cut line on the workpiece. Do not allow the Saw Blade to come in contact with the workpiece. 4. Turn the Laser Switch (4) to its “ON” position, and align the laser beam with the cut line on the workpiece. 5. Squeeze the Trigger to turn on the Jigsaw. If operating the Jigsaw for an extended period of time, you may wish to depress the Trigger Lock (61) to lock the Trigger in its “ON” position. 6. Allow the Saw Blade (59, 60) to stroke at full speed before feeding it into the workpiece. 7. Make sure to hold the Jigsaw firmly with both hands, as torque from the Motor will cause the tool to twist. Then, slowly make the cut . (See Figure D.) 8. When finished, squeeze and release the Trigger to put it in its off position and stop the Jigsaw. Wait until the Saw Blade (59, 60) stops completely. Turn the Laser Switch (4) to its “OFF” position. Then, remove the Jigsaw from the workpiece. 9. To prevent accidents, turn off the tool and disconnect its power supply after use. Clean, then store the tool indoors out of children’s reach. MAINTENANCE AND SERVICING Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Squeeze and release the Trigger to put it in its off position and unplug the tool from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the tool. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. 2. AFTER USE, wipe external surfaces of the tool with clean cloth. 3. WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician. Troubleshooting Problem Possible Causes Likely Solutions Tool will not start. 1. Cord not connected. 2. No power at outlet. 3. Tool’s thermal reset breaker tripped (if equipped). 4. Internal damage or wear. (Carbon brushes or switch, for example.) 1. Check that cord is plugged in. 2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker. If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads. 3. Turn off tool and allow to cool. Press reset button on tool. 4. Have technician service tool. Tool operates slowly. Extension cord too long or wire size too small. Eliminate use of extension cord. If an extension cord is needed, use shorter/heavier gauge cord. See Extension Cords in GROUNDING section. Performance decreases over time. 1. Accessory dull or damaged. 2. Carbon brushes worn or damaged. 1. Keep cutting accessories sharp. Replace as needed. 2. Have qualified technician replace brushes. Exc...