valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. 0 When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. 0 If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Mounting blade First, use the hex wrench to remove the Hex wrench bolt which secures the blade clamp to the blade holder shaft. With the blade teeth facing forward, place the shank of the blade over the flat side of the blade holder shaft. Then place the blade clamp over the other side of the blade shank. Secure this assembly together with bolt. Make sure that the bolt passes through the larger hole in the blade shank. Using roller With the hex wrench loosen the bolt which holds the base and retainer. Slide the re- tainer so that the roller contacts the blade, then tighten the bolt. w SDrina washer Blade clamp h Blade holder shaft Retainer II \ ' Roller Blade IU Use a lubricant or cutting oil between the blade and roller when cutting metals. Failure to do so will shorten the service life of your blade and roller. CAUTION : 0 Before inserting the battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. 0 When not operating the tool, keep the lock-off lever in the SAFETY LOCK position. .Pulling the trigger hard when the lock-off lever is set to the SAFETY LOCK position can cause switch breakage. Operation Turn the tool on before contacting the workpiece. Then rest the base flat on the workpiece and gently move the tool for- ward along the previously marked cutting line. Plunge cutting Starting a cut at other than the edge of the workpiece without first drilling a starting hole requires a "plunge cut." This can be accomplished by tipping the tool forward until the front end of the base rests against the workpiece. Switch the tool on and lower the back end of the tool slowly, gradually allowing the blade to saw through the wood until the base is able to sit flat on the work- piece. You may then proceed forward with the cut in a normal manner. If using a drill for a starting hole, bore a hole over 12 mm (1/2") in diameter. Then insert the blade in it and proceed. Front flush cuts Loosen the bolt on the back of the base with the hex wrench, then slide the base backwards. Check the contact between the back edge of the blade and support roller, then secure the bolt. Bevel cutting 1. With the base tilted, you can make bevel cuts at any angle between 0" and 45' (left or right). 1 Roller 1 Edge of housing i 9 Finishing edges To trim edges or make dimensional adjust- ments, run the blade lightly along the cut edges. For smoother cutting of plywoods or other materials with easily splintered surfaces, the wood may be coated or transparent tape used over your cutting line. Using guide rule (Rip fence) When cutting widths of under 150mm(6") repeatedly, use of the guide rule will assure fast, clean cuts. Attaching guide rule (Rip fence) To attach the guide rule (rip fence), secure the rule holder to the base with the hex screw (do not tighten). Insert the guide rule between the base and the rule holder. Now tighten the hex screw with the hex wrench. Guide Using circular guide 1. Use of the circular guide insures clean, smooth cutting of circles (radius; under 200 mm; 7-7/8")and arcs. 2. When attaching the circular guide, use the pin, inserting it in the center hole (arrow) and secure it with the threaded knob. The circular guide attaches to the base of the tool in the same manner as the guide rule (rip fence). Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear. 0Knob Fit pin into this hole Pin for circular guide I- ll Cutting performance Material Thickness Cutting length The following reference table indicates the approximate cutting capacity from a single Soft wood 1-hour battery charge. It may differ under (,5,,6") 2.5 m (8.2 ft) some conditions. Hard wood I Mild steel CAUTION : I ;&:: 1 3 m (9.8 ft) ::,;: I 4 m (13ft) If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. Hex wrench storage When not in use, the hex wrench can be conveniently stored. L 1 Hole The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. MAINTENANCE CUATION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, ...
Questo manuale è adatto anche per i modelli :Jig Saw e - 4307DW (962.75 kb)