valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
L1. The blade teeth will dig into the scrap wood and prevent rotation of the blade. • Tighten the blade clamping screw securely with the blade wrench. NOTE: The blade wrench is stored in the saw housing as shown in figure M. Lower Blade Guard WARNING: Laceration Hazard. The lower blade guard is a safety feature which reduces the risk of serious personal injury. Never use the saw if the lower guard ismissing, damaged, misassembled or not working properly. Do not rely on the lower blade guard to protect you under all circumstances. Your safety depends onfollowing all warnings and precautions as well as proper operation of the saw. Check lower guard for proper closing before each use as outlined in AdditionalSafety Rules for Circular Saws. If the lower blade guard is missing or not working properly, have the saw serviced before using. To assure product safety andreliability, repair, maintenance and adjustment should be performed by an authorized service center or other qualified service organization, always usingidentical replacement parts. WARNING: To minimize the risk of eye injury, always use eye protection. Carbide is a hard but brittle material. Foreign objects in the work piece such as wire or nails can cause tips to crack or break. Only operate saw when proper saw blade guard is in place. Mount blade securely in proper rotation before using, and always use a clean, sharp blade. CAUTION: Do not cut ferrous metals (steel), masonry, glass or tile with this saw. A dull blade will cause slow, inefficient cutting overload on the saw motor, excessive splintering, and could increase the possibility of kickback. 13 90537965 BD Circ Saws 5/30/08 10:11 AM Page 14 SWITCH Saw is equipped with a switch lock-off feature to prevent unintentional running. • To operate the tool, press in on the lock-off button (2) from either side of the saw and hold it in as you depress the trigger switch (1). • After you have depressed the trigger and the tool is running, release the lock-off button. The tool will continue to run as long as the trigger is depressed. • To turn the tool off, release the trigger switch. NOTE: This tool has no provision for locking the tool on, and the switch should never be locked on by any other means. AUTOMATIC ELECTRIC BRAKE Your saw is equipped with an electric blade brake which stops the saw blade within 1-1/2 seconds of trigger release. This is automatic and requires no adjustment. Occasionally, under certain conditions, the brake will not function properly and won’t stop the saw in the 1-1/2 seconds as discussed above. If this condition occurs: • Turn the saw on and off four or five times. • If the problem still persists, have the tool serviced at a Black & Decker service center or company authorized service facility. OPERATING THE LASER - (BDCSL1806 ONLY) INSTALLING THE BATTERIES - FIGURE N WARNING: LASER RADIATION. BE CERTAIN THE LASER ON/OFF BUTTON IS IN THE OFF POSITION (SEE SECTION “SWITCHING THE LASER ON AND OFF) BEFORE INSTALLING BATTERIES. Lift the battery door (25) off the laser module (4) by gently squeezing the front of the door as shown in figure N. Insert 2 fresh 1.5 volt AAA batteries making sure to match (+) and (-) terminals correctly. Reattach the battery door. WARNING: Batteries can explode, or leak, and can cause injury or fire. To reduce this risk: • Carefully follow all instructions and warnings on the battery label and package. • Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment. • Do not short battery terminals. • Do not charge batteries. • Do not mix old and new batteries. Replace all of them at the same time with new batteries of the same brand and type. • Remove dead batteries immediately and dispose of per local codes. • Do not dispose of batteries in fire. • Keep batteries out of reach of children. • Remove batteries if the device will not be used for several months. “Transporting batteries can possibly cause fires if the battery terminals inadvertently come in contact with conductive materials such as keys, coins, hand tools and the like. The US Department of Transportation Hazardous Material Regulations (HMR) actually prohibit transporting batteries in commerce or on airplanes (i.e. packed in suitcases and carryon luggage) UNLESS they are properly protected from short circuits. So when transporting individual batteries, make sure that the battery terminals are protected and well insulated from materials that could contact them and cause a short circuit.” ON BOARD LASER Your saw is equipped with an on board laser which is turned on and off separately from the saw. WARNING: LASER RADIATION. Never aim the beam at a workpiece with a reflective surface. Bright shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator. DANGER: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Nev...
Questo manuale è adatto anche per i modelli :Jig Saw e - 90537965 (4.5 mb)
Jig Saw e - BDCS1806 (4.5 mb)
Jig Saw e - BDCS1807 (4.5 mb)
Jig Saw e - BDCS2406 (4.5 mb)