valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
Failure to do so can cause stalling and kickback. Any other conditions which could result in pinching, binding, twisting, or misalignment of the blade could cause kickback. Refer to the sections on “Adjustments and Set-Up” and “Operation” for procedures and techniques that will minimize the occurrence of kickback. TOOL LUBRICATION NOTE: With a new saw, change the oil after the first 10 hours of use and once per year after that. This action will greatly extend the life of your unit. 1. Always check oil level before rLUu uim iibbiut using the saw. To check the oil level, lay the saw down on the blade side, shown in Figure 12 and remove the oil filler plug. 2. Lay the plug on its side under the top edge of the blade guard as shown. This procedure ensures that the saw is level so that the oil can be checked accurately. If the saw is adequately lubricated, oil will be visible at lower edge of the oil filler hole within 25 seconds. If oil does not appear in this time, the saw requires lubrication. 3. To lubricate the saw, stand it on its handle end. Add lubricant to the oil filler hole, checking frequently as described above to determine when the proper level is reached. If you accidentally overfill the saw, lay it on its side and permit the excess to leak out until the proper level is obtained. DO NOT OVERFILL SAW! Pressure generated by the gears in an overfilled saw will force lubricant through the seals causing eventual gear failure and possible motor damage. Brushes TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. Inspect carbon brushes regularly by unplugging tool, removing the brush inspection cap and withdrawing the brush assembly. Keep brushes clean and sliding freely in their guides. Always replace a used brush in the same orientation in the holder as it was prior to removal. Carbon brushes have varying symbols stamped into their sides, and if the brush is worn down to the line closest to the spring, they must be replaced. New brush assemblies 7 are available at B&D service centers. The tool should be allowed to “run in” (run at no load without a blade) for 10 minutes before use to seat new brushes. While “running in” DO NOT TIE, TAPE, OR OTHERWISE LOCK THE TRIGGER SWITCH ON. HOLD SWITCH BY HAND ONLY. Blades A dull blade will cause slow, inefficient cutting overload on the saw motor, excessive splintering, and could increase the possibility of kickback. It is a good practice to keep extra blades on hand so that sharp blades are available while the dull ones are being sharpened. (See “Saws-Sharpening” in the yellow pages.) In fact, many lower priced blades can be replaced with new ones at very little cost over the sharpening price. Hardened gum on the blade will slow down the cutting. This gum can best be removed with kerosene, turpentine, or oven cleaner. B&D manufactures a complete line of saw blades and the following types of blades are available from your dealer. Combination Blade- For general-purpose ripping and cutting. Chisel Tooth Combination- Specially designed for general-purpose ripping and crosscutting. Framing/Rip Combination- For facing, roofing, siding, sub-flooring, framing, form cutting. Cross Cut Blade- For smoother, faster cross cutting. Ripping Blade- Fast for rip cuts. Plywood Blade- For smooth cuts in plywood. Reduce splintering. Planer Blade- For very smooth ripping and cross cutting. Flooring Blade- For sawing where nails may be occasionally encountered. Metal Cutting Blade- For cutting aluminum, copper and other soft metals. Friction Blade-For cutting corrugated, galvanized sheets. Carbide Tipped Blade- For longest sawing without blade sharpening. Cuts wood, transite, cemesto board, asbestos, formica, masonite, and similar materials. ACCESSORIES Recommended accessories for use with your tool are available at extra cost from your distributor or your local service center. A complete listing of service centers is included with your tool. Kit Box: 7-1/4“, and 8-1/4" saws- (Cat # 62864) Lubricant: This special lubricant has been developed to add longer life to worm drive saw gears. See lubrication instructions. (6 oztube- Cat# 60086) Rip Fence - (Cat# 60551) Inner Ciamp Washer is used on all worm drive saws when using metal or abrasive blades with round arbor holes. (Cat# 63243) Inner Clamp Washer is used on all worm drive saws when using metal or abrasive blades with diamond arbor holes. (Cat# 143783) Outer Clamp Washer is used on all worm drive saws on the outer side off all metal or abrasive blades. (Cat# 70457-00) WATER FEED ATTACHMENTS ARE NOT RECOMMENDED FOR WORM DRIVE SAWS. CAUTION: The use of any non-recommended accessory may be hazardous. If you need any assistance in locating any accessory, call 1-800-9-BD TOOL (1-800-923-8665) or contact Black & Decker, Consumer Services Department, 626 Hanover Pike, P.O. Box 618, Hampstead, MD 21074. IMPORTANT! To assure product SAFETY and RELIABILITY, particularly for double insulated tools, repairs, mainte...
Questo manuale è adatto anche per i modelli :Jig Saw e - 2700 (4.43 mb)
Jig Saw e - 2701 (4.43 mb)