valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
Always use the proper sizeextension cords with the tool – that is, proper wire size for various lengths of cord and heavyenough to carry the current the tool will draw. Use of an undersized cord will cause a drop inline voltage resulting in loss of power and overheating. For proper size cords see chart. Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more American Wire Gage Than Than 0-618 16 16 14 6 -10 18 16 14 12 10-12 16 16 14 12 12 -16 14 12 Not Recommended Motor Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DCpower. This information is printed on the nameplate. Lower voltage will cause loss of powerand can result in over-heating. All Black & Decker tools are factory-tested; if this tool doesnot operate, check the power supply. SAVE THESE INSTRUCTIONS Assembly WARNING: Sharp blade. To prevent accidental operation, turn off and unplug sawbefore performing the following operations. Failure to do this could result in serious personal injury. Fitting the saw blade (fig. A) -Hold the saw blade (7) as shown, with teeth facing forward. -Push the lever (4) downwards. -Insert the shank of the saw blade into the blade holder (15) as far as it will go. -Release the lever. -Adjust the blade support roller as described below. AccuCutTM blade support roller (fig. B) After fitting the blade, you need to adjust the blade support roller (5). Screwdriver Method -Turn the slotted blade support adjustment screw (6) in direction A. -Slide the blade support roller against the rear of the blade. The blade must locate in the central recess of the roller. -Turn the blade support adjustment screw in direction B to lock the blade support in place. Tool Free Method -The blade support roller can be adjusted in a “tool free” manner, by turning the scroll ing knob (8) so that the adjustment screw is rotated around to the front of the unit where it canbe turned by hand. Connecting a vacuum cleaner to the tool (fig. C & D) -Align the dust extraction adaptor (14) with the saw shoe as shown. -Insert the ribs (16) into the slots (17). -Pull the adaptor towards the rear of the jigsaw to secure. -Connect the vacuum cleaner hose (18) (not supplied) to the adaptor. -Dust extraction is not possible when making bevel cuts. WARNING: Fire Hazard. Do not use vacuum adapter when cutting metal. Metal filings will be hot and could cause a fire in the vacuum container. Operation WARNING: Laceration Hazard. To prevent loss of control, never use the tool whenthe saw shoe is loose or removed. Failure to do this could result in serious personal injury. Adjusting the shoe plate for bevel cuts (fig. E) The shoe plate can be set to a left or right bevel angle of up to 45°. -Turn the locking knob (11) in direction A to release the shoe plate (10). -Pull the shoe plate (10) backwards and set it to the required angle. You can use the scale or a protractor to check the angle. -Turn the locking knob (11) in direction B to lock the shoe plate in place. To reset the shoe plate for straight cuts: -Turn the locking knob (11) in direction A to release the shoe plate (10). -Pull the shoe plate backwards and set it to an angle of approximately 0. -Push the shoe plate forward. -Turn the locking knob (11) in direction B to lock the shoe plate in place. Make sure that the shoe plate is supported by the guide ribs. Variable speed control -Set the variable speed control knob (3) to the required speed range. Use a high speed for wood, medium speed for aluminum and PVC and low speed for metals other than aluminum. Switching On and Off -To switch the tool on, press the on/off switch (1). -For continuous operation, press the lock-on button (2) and release the on/off switch. -To switch the tool off, release the on/off switch. To switch the tool off, when in continuous operation, press the on/off switch once more and release it. Using the mode selector The mode selector (9) can set in 3 positions 1. Scrolling position (figs F and G) - this position allows the scroller knob (8) to be rotated for intricate and accurate sawing. (In this position there is no orbital action.) It is recommended to use scroller blades when in this mode. 2. Straight cutting position (figs Ha, Hb and Hc ) this position turns off orbital action and locks the scroller knob to prevent its rotation. The scroller knob can be locked in any of 4 positions for straight cutting. Method of engagement: a. Turn the Mode Selector to the scrolling position. b. Rotate the scroller knob to the desired position (this can be any of 4 positions - theblade can point forwards, reverse, left or right). c. Turn the Mode Selector to the neutral position. (In this position the Scroller Knob cannot be turned). 3. Orbital Actio...