valutazioni - 4, GPA: 4.5
(
)
)
|
Facilità d'uso
Decker. SAFETY PRECAUTIONS WITH SAWS BRUSHES 1, Disconnect plug from power supply before changing blades, making cutting depth or cutting angle adjustments, lubricating, inspecting* or when saw is not being used. 2, When retracting thte lower blade guard, always use the retracting knob on the guard. 3, Never tie back the lower blade guard or its retracting knob, 4, When sawing never reach underneath the material for any reason, 5, Always be sure that the saw will be properly grounded before plugging into power supply. See following section. S. Keep blade sharp..Dull blades may cause the saw to swerve or stall under pressure. 7, Wear safety goggles when the cutting of material results in flying particles. If material forms dust when cut, also use a dust mask. 8, If you drop or damage the saw, unplug it first; then check to see if the blade and lower blade guard, operate freely before resuming operations. 9, If saw stalls, release the trigger and disconnect plug from power supply before attempting to loosen the unit. GROUNDED OUTLET I Fig, Л GROUNDING BLADE II TUI LONGEST Of THE 3 BLADES GREEN GROUNDING a/ ■oí GROUNDED OUTLET _ I BOX Fig. В GROUNDING EVERY ELECTRIC TOOL SHOULD BE GROUNDED while in use to protect the operator against shock. This unit is equipped with approved 3-conductor cord and 3-blade grounding type attachment plug to be used with the proper grounding type receptacle. The green colored conductor in the cord is the grounding wire. Never connect the green wire to a “live" terminal. If your unit requires less than 150 volts, it has a plug that looks like fig. “A". A special grounding adapter (Fig. “B”) is available from your dealer to permit using 2-wire receptacle until the correct receptacle is properly installed. The green grounding wire extending from the side of the adapter must be connected to a PERMANENT GROUND such as a properly grounded outlet box. If you use an extension cord, be sure that it is a 3-conductor, grounding-type cord. Grounding must be continuous from the tool plug to a grounded receptacle. EXTENSION CORD When using the tool at a considerable distance from power source, a 3-wire grounding-type extension cable of adequate size must be used for safety and to prevent loss of power and over-heating. Use the table at right for 120-volt tools. For 220-voIt tools, use wire size corresponding to an extension length of y2 the contemplated length. FT.I. Safety Rule #12 applies to Extension Cords as well as the Tool Power Cord. Before using cords, inspect them for loose or exposed wires and damaged insulation. Make any needed repairs or replacement before using your power tool. Ext. cable length in feet ..25 50 75 100 Required wire size (A.W.G.) in cable.. 16 14 12 10 Carbon motor brushes should be inspected frequently for wear. To inspect brushes, FIRST,: UNPLUG SAW FROM POWER SUPPLY. Then, with a screwdriver, slide the brush cover plates outward and the brush spring will pop out. Put the spring, with attached wire extended out of the opening into the position shown at right and tilt the saw so that the carbon brush will drop out of the opening. If the brush is worn down to the grooved line on its side, a new brush is needed and can be obtained from any of the locations shown on the next page. To reassemble, insert brush with worn end toward motor, or a' new brush with longest distance from end to grooved line toward motor. Next, insert the small brass plate behind the brush, and then feed in the spring until the round spring cap fits flush with the opening. This allows the cover plate to be pushed back iato the closed position. OWNER’S MANUAL KNOB FOR RETRACTING LOWER BLADE GUARD TRIGGER SWITCH: PULL-"0N”; RELEASE-“OFF’ ACCESSORIES Л WP FENCE Quickly attaches for fast, smooth rip cuts without penciled guide lines. 04914 49531 SAW PROTRACTOR Permits accurate cuts, 0° to 90° angles. Saves time and effort. 55582 CUT-OFF GUIDE One-piece die-cast aluminum guide for making accurate cuts. GUIDE LINE FOR VERTICAL CUTS SLIDING BRUSH COVER PLATE CUTTING DEPTH * ADJUSTMENT THE BLACK & DECKER MFG. CO., T0WS0N, MD. 21204, U.S.A. CUTTING DEPTH: At 90° - Vs" to 23/a". At 45° bevel — 0" to 1 BEVEL ADJUSTMENT: 0° to 45°. 120 VOLTS A.C. ONLY 9.5 AMPS 1 ]/2 H.P. 4700 R.P.M. 7'/«” CIRCULAR SAW model 3004 Form No. 97243 AL Printed in U.S.A. SAFETY RULES FOR POWER TOOLS 1, KNOW YOUR POWER TOOL — Read owner's manual carefully. Learn its applications and limitations as well as the specific potential hazards peculiar to this tool, GROUND ALL TOOLS - UNLESS DOUBLE-INSULATED. If tool is equipped with three-prong plug, it should be plugged into a three-hole electrical receptacle. If adapter is used to accommodate two-prong receptacle, the adapter' wire must be attached to a known ground. Never remove third prong, KEEP GUARDS IN PLACE and in working order, KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents. AVOID DANGEROUS ENVIRO...
Questo manuale è adatto anche per i modelli :Jig Saw e - 97243 AL (2.78 mb)