valutazioni - , GPA:
(
)
)
Produttore : Craftsman
File Size : 762.27 kb
File Nome : a37db620-d717-4d9e-b908-3dc58b6faa9a.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
14 Squeeze the switch trigger to start your saw. Always let the blade reach full speed, then guide your saw into the workpiece. _IL WARNING: The blade coming in contact with the workpiece before it reaches full speed could cause your saw to "kickback" towards you resulting in serious injury. When making a cut use steady, even pressure. Forcing causes rough cuts, could shorten the life of your saw and could cause "kickback." REMEMBER: When sawing through work, the lower blade guard does not cover the blade, exposing it on the underside of work. Keep your hands and fingers away from cutting area. Any part of your body coming in contact with the moving blade will result in serious injury. After you complete your cut release the trigger and allow the blade to come to a complete stop. Do not remove your saw from workplece while the blade is moving. _l, CAUTION: When lifting your saw from the workpiece, the blade is exposed on the underside of your saw until the lower blade guard closes. Make sure lower guard is closed before setting your saw down on work surface. TO CROSS CUT OR RIP CUT When making a cross cut or rip cut, align your line of cut with the outer blade guide notch on the saw base as shown in figure 15. ALIGNOUTERBLADEGUIDENOTCHON SAWBASEWITHLINEOFCUTAS SHOWN GUIDELINE WHENMAKINGCROSSCUTSORRIPCUTS Fig. 15 Since blade thicknesses vary, always make a trial cut in scrap material along a guideline to determine how much, if any, the guideline must be offset to produce an accurate cut. NOTE: The distance from the line of cut to the guideline is the amount you should offset the guideline. OPTIONAL EDGE GUIDE (RIP GUIDE) Use a rip guide when making rip cuts up to five inches wide. It helps prevent the blade from twisting in a cut. The blade twisting in a cut can cause kickback. A rip guide is available at your Sears Catalog Order or Retail Store. TO ASSEMBLE RIP GUIDE • Unplug your saw. _1= WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury; • Place rip guide through holes in saw base as shown in figure 16. PLACERIP EDGEGUIDE GUIDETHRUHOLES Fig. 16 Page 12 • Adjust rip guide to the length needed for the cut. • Tighten edge guide screw securely. When using a rip guide, position the face of the rip guide firmly against the edge of workpieca. This makes for a true cut without pinching the blade. The guiding edge of workplace must be straight for your cut to be straight. Use caution to prevent the blade from binding in the cut. TO BEVEL CUT The angle of cut of your saw may be adjusted to any desired setting between zero and 51.5 ° . NOTE: When making cuts at 51.5 ° blade should be set at full depth of cut, with edge guide screw removed. When making 45 ° bevel cuts, there is a notch in the saw base to help you line up the blade with the line of cut. See Figure 17. BEVEL SCALE BEVEL NOTCH ADJUSTMENT WING NUT ALIGNINNERBLADEGUIDENOTCHON SAW BASEWITHLINEOF CUTAS SHOWNWHEN MAKING45° BEVELCUTS Fig. 17 Align your line of cut with the inner blade guide notch on the saw base when making 45° bevel cuts. Since blade thicknesses vary and different angles require different settings, always make a trial cut In scrap material along a guideline to determine how much you should offset the guideline on the board to be cut. When making a bevel cut hold your saw firmly with both hands as shown in figure 18. LOWER BLADEGUARD Fig. 18 Rest the front edge of the base on the workpiece. Squeeze the switch trigger to start your saw. Always let the blade reach full speed, then guide your saw into the workpiece. _1= WARNING: The blade coming in contact with the workpiece before it reaches full speed could cause saw to "kickback" toward you resulting in serious injury. After you complete your cut release the trigger and allow the blade to come to a complete stop. After the blade has stopped, lift your saw from the workplace. TO ADJUST BEVEL SEI-I'ING • Unplug your saw. _1, WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. • Loosen wing nut. See Figure "17. • Raise motor housing end of saw until you reach desired angle setting on bevel scale. See Figure 17. • Tighten wing nut securely. _i, WARNING: Attempting bevel cut without wingnut securely tightened can result in serious injury. Page 13 POSITIVE0° BEVEL STOP See Figure 19. BEVEL ADJUSTMENT ADJUSTMENT SCREW WINGNUT HEXNUT POSITIVEO°BEVELSTOP SAWBLADE CARPENTER'SSQUARE \ Fig. 19 Your saw has a positive 0° bevel stop, that has been factory adjusted to assure 0° angle of your saw blade when making 90 ° cuts. However, misalignment can occur during shipping. TO CHECK • Unplug your saw. ,_ WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. • Place your saw in an upside down position on workbench. See Figure 19. • Using a carpenter's square, check squareness of saw blade to the base of your saw. TO ADJUST • Unp...
Questo manuale è adatto anche per i modelli :Jig Saw e - 315.10833 (762.27 kb)