valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
1) Before allowing anyone to operate the lift, be certain they fully understand the proper operating procedures. 2) Be certain to install the lift as specified in instruction manual. Not doing so can cause equipment damage and or personal injury. 3) Always wear leather gloves when handling wire rope. 4) All electrical equipment must be inspected and installed by a certified electrician in accordance with local electrical codes. 5) Have your electrician ensure that a Ground Fault Circuit Interrupter (G.F.C.I.) is installed and working properly. 6) Tighten all nuts and bolts securely before using the lift. 7) Keep people and pets away from lift during its operation. Do not allow swimming or playing around or on the lift. 8) Do not exceed the maximum weight capacity of the lift that can lead to serious personal injury and/or equipment failure. 9) Completely remove all loads from the lift before performing any type of maintenance or repair on it. 10) Do not work on or in the boat when it is attached to the lift. 11) Periodically inspect the wire rope for wear or damage. Check the wire rope ends to ensure that they are securely fastened. Immediately replace any worn or damaged wire rope. 12) Inspect the pulleys and bearings to be certain that they spin freely. Lubricate or replace them immediately. 13) A boat with water in it from a rain storm may exceed the weight capacity of the lift. Be certain to drain the boat before lifting it all the way up to its resting place. Make sure you replace the plug before launching your boat. Rounded Rectangle: SAFETY PRECAUTIONS INSTALLATION AND SETUP PRE-INSTALLATION CHECKS 1. Insure you have received all specified parts as listed in supplied parts list. 2. Consult licensed professional engineer to inspect and approve boathouse structure for this type of application and loading capacity. WARNING: INSURE BOATHOUSE STRUCTURE HAS BEEN DESIGNED FOR THIS TYPE OFAPPLICATION AND CONSTRUCTED IN ACCORDANCE WITH LOCAL BUILDING ANDELECTRICAL CODES TO PREVENT PERSONAL INJURY AND / OR EQUIPMENTDAMAGE. 3. Do not install or use the lift if it shows any signs of damage. 4. Do not weld or otherwise modify any part of the lift or power drive. Such alterations may damage the lift and / or power drive and void the associated warranties. 5. Two people will be needed to mount the power drive into the boathouse. The following precautions must be observed when lifting any part of this equipment: a. Be sure of your footing. b. Bend your knees and lift with your legs. c. Hold the equipment section close to your body when lifting. WARNING: USE A MINIMUN OF TWO PERSONS TO INSTALL THE POWER DRIVE INTO THEBOATHOUSE TO PREVENT PERSONAL INJURY AND/OR EQUIPMENT DAMAGE. LIFT ASSEMBLY Supporting beams must be installed to the spacing required by the boat to be lifted. The hangers will fit beams 6” wide by 6” to 9” deep. 1. Assemble #37X and #38X hangers and clamps to each corner of the boathouse beams about 6” wider than the beam of the boat. 2. Using 2 x 6 or 2 x 8 pressure treated wood planks, construct two mounting bases for the power drives. Center them on the fore and aft beams between the hangers. 3. Temporarily clamp the power drive to the wood mounting base and position it so that the centerlines of the speed reducers are askew to the centerlines of the two boathouse beams. Ensure that the power drive is positioned to that the winch spools are at right angles to the wire rope line pull. Refer to the reeving diagram. 4. When the power drive is positioned properly, drill two 1/2” holes through the wood mounting base using the power drive frame as a template. Fasten the frame in place with the supplied 1/2” hardware, reference part # 8, 9 and 10. 5. Remove pipe plugs on sides of the reducers closest to the ceiling of boathouse and install supplied vent plugs. CAUTION: FAILURE TO INSTALL THE VENT PLUG CAN CAUSE PREMATURE FAILURE OF THEREDUCER SEALS AFTER EXTENDED USE AND VOID YOUR WARRANTY. 6. Mount the reversing switches in a suitable location protected from water and near enough to each other to allow for easy operation. 7. Assemble safety latches to ends of hooks. Attach hooks to plain double blocks with shackles. 8. Attach pulley blocks to all hangers as shown in diagram. 9. Reeve the wire rope through the blocks and spools as shown. Be careful to wind the rope in tight, even layers on the spools. If the wire rope is wound properly from the beginning it will not kink or break the wire strands. Secure cable ends with wire rope clamps. 10. Attach the slings or I-beam cradles to the lifting blocks per their instruction. 11. Refer to Power Supply Connections Section Before Proceeding. 12. Pull the boat into the lift and raise it up slowly. If one corner tightens before the others, lower the boat. 13. Slide some wire rope through the loop in the spool from the loose corner toward the tight one to level the boat. If the blocks twist on themselves when unhooked, loosen the cable clamps at the block and unwind...