valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
17 . 1 pair of universal pliers LIST OF PARTS Hulls (2) Front crossbar Rear crossbar Mast Boom Trampoline Part bag (wires) Rigging bag Ropes bag Rudder assemblies (2) Tiller crossbar Tiller extension Mainsail + battens (7) Jib Trampoline lacing rod Daggerboards (2) It is advisable to be at least 2 people to assemble the Hobie Tiger . CAUTION - DANGER ALUMINIUM MAST - STAY AWAY OF ELECTRICAL WIRES 2 List of parts 1 2 4 5 6 9 ROPES : All ropes are labelled with ref. number and name. Please check carefully before using. 1. Righting line (white) 2. Trapeze shock cord (white) 3. Jib sheet (yellow) 4. cunningham line (red) 5. Mainshjeet (black and yellow) 6. Jib halyard rope 7. 10. Rotation line 8. jib sheet shock cord 9. Jib clew line 11. Bout etarquage de foc 1 2 6 7 8 3 7 8 3 4 5 9 10 11 WIRES : 1. Shrouds 2. Bridles 3. Spreader diamond wires 4.5. Jib halyard + forestay 6.7. Trapeze wires 8. Spreader wire 9. Stay adjuster cover 3 Hull assembly Position the hulls in parallel with the inner sides facing the ground. Lift the right hull. One person straddles the hull to hold it in place. The other person applies the silicone sealant (for waterproofing) around the screw holes. 1 Take the front crossbar (with dolphin striker). Place it in its support so that the trampoline track faces the rear of the boat. Insert the two bolts. Pass your hand through the inspection port to position the nuts and washers onto the screws photo). Fasten loosely. Lift the left hull, and follow the same steps as for the right hull. Do not fully tighten the screws. ***Respect same order for the washers as assembled at the delivery*** 2 Apply silicone sealant around the screw holes at the back of the hulls. Place the rear crossbar on the right side. Insert the bolts, washers and nuts as shown for the front crossbar. Do the same thing for the left side. Once the frame has been mounted, tighten all the bolts fully and then install the lock nuts. 3 It is advisable to check the fastening of the bolts after the first trip out onto the water, and recheck these at regular intervals. 4 Trampoline Unfold the trampoline. Note that the side tension lines are prethreaded. Insert the front sealed bolt rope edge into the trampoline track of the front corssbar. Continue feeding the trampoline into the trampoline track and position it in the centre. Line up the grommet in the centre of the front edge of the trampoline with the dolphin striker 1 Pull the trampoline to the back of the boat and insert the fibreflass rod into the rear flap of the trampoline. Leave an equal amount protruding from each side. 2 Commence lacing the rear of the trampoline. The lacing line ties off on the lacing post at the left rear of the rear beam. Pass the line around the rod and back around the first lacing post. Lead the line around the second lacing post and pass it around the rod on the first trampoline cut out. Now, come back around the second lacing post and continue towards the third. Continue all the way across the beam in the same fashion and tie off loosely. Do not attempt to tighten the rear lacing too much at this stage. 3 Beginning Tensioning the sides : starting at the right rear corner, take the line that emerges from the trampoline. Lead it through the eye strap on the rear beam and then through the grommet/eyelet. Tie it off with a bowline knot or similar. 4 Move to the front right corner of the trampoline. Pull on the line as firmly as possible and tie a bowline knot or loop in the line as close to the trampoline edge as possible. This will enable a 2:1 purchase to be used for tensioning. Tie off once tensioned to secure. 5 Now lead the end of the line through the eyestrap on the rear of the front beam and back through the loop. Lead the end back through the eyestrap and apply as much tension as possible. Maintaining the tension, lead the line through the grommet and back to the eyestrap. Next, lead the line through the grommet in the front edge of the trampoline and tie off securely. Repeat procedure for port side. 6 5 Trampoline 7 Retighten rear lacing from left to right. Tie the rear lacing off securely at the eyelet posts on the right hand end of the rear beam. NB : It is important that the trampoline lacing is kept very tight. NB : Check the trampoline tension on a regular basis. Remember : all ropes streches! 6 Rudder assembly Identify the right rudder from the left rudder (green sticker = right ; red sticker = left) Take the left rudder, and align the upper rudder casting onto the rear gudgeon. 1 Repeat the procedure for the right rudder assembly. 3 Insert the rudder pin, and do not forget to put in the two split rings: one on top and one at the bottom of the rudder pin. 2 7 Tiller crossbar & extension Take the tiller crossbar and insert the right side into the right rudder arm and the left side into the left rudder arm. 1 Take the yoke connection of the tiller extension and fix it into the middle of the tiller crossbar Then fix the tiller head into the ...