valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
Please use caution to prevent accidental closing. V-Drive Engine Compartment SUPRA - 38 © 2005 Skier’s Choice, Inc. Fire Extinguisher A standard United States Coast Guard approved fire extinguisher is provided with your Supra boat. The fire extinguisher is usually located under the observer’s seat cushion, however, locations vary by boat. You should know the exact location of your boat’s fire extinguisher in case of an emergency. NOTICE: Refer to the instructions on the fire extinguisher for proper use. Flame Precautions Sparks while fueling can cause explosion! Extreme caution should be taken when an open flame is present on board. Fumes from the engine and fumes from the battery are highly flammable. No flame or spark should come near these areas. V-Drive Ski Pylon The ski pylon is to be used to pull skiers. DO NOT use ski pylon to hoist boat! Only use the lifting rings for this purpose. The 24 Series boat has a retractable ski pylon. To use, pull pylon up, twist counterclockwise and push back down into the lock position. To retract, pull pylon up, twist clockwise and push down to storage position. DO NOT mount any Pylon Extension on the rear pylon (located at the rear sundeck). Inboard Ski Pylon The ski pylon is located in the center portion of the boat directly in front of the motor box. The ski pylon is to be used to pull skiers. DO NOT use ski pylon to hoist boat! Only use the lifting rings for this purpose. NOTICE: The use of pylon extensions may cause the pylon to loosen. Please see your dealer for proper tightening procedures. The use of pylon extensions can severely effect the overall handling of the boat. Follow pylon extension manufacturers directions for mounting. © 2005 Skier’s Choice, Inc. SUPRA - 39 Rad-A-Cage Style 1 To Lower Cage For Storage Tools Required: 5/16” Allen Wrench 1.Loosen (but do not remove) the front 5/16-18 x 1-1/4” allen head bolts that connect the front legs to the foot. 2.Remove the hand knobs of the rear feet. 3. While standing in the bow area, pull the cage forward, gently placing it against the bow of the boat. Place padding between the cage and the boat to protect the gel coat finish from scratches. To Raise The Cage Lift and rock the tower back into place until the rear legs align with the rear feet. (Some manipulation of the cage may be required to get the legs to line up with the feet). Install both bolts and tighten all bolts. The threads in the aluminum foot could be damaged if the bolts are not aligned and threaded correctly! Rad-A-Cages are designed to pull one wakeboarder, kneeboarder or trick-skier. If your Supra model has been equipped with an optional RAD-A-CAGE towing tower, please review this section for details on it’s usage, maintenance and storage. The cage is designed as a stable tower to enhance wakeboarding. It is NOT intended to be used to tow skiers, barefoot skiers, or multiple wakeboarders. Such use will void any warranties written or implied. Before use, be sure that all mounting bolts are properly tightened in place. Be aware of and avoid low overhead objects such as bridges, power lines, overhanging trees, etc. Style 2Style 1 Style 2 To Lower Cage for Storage -Remove the four hand knobs from the top of the rear leg. While holding the tower up, lower the side legs. Then lower the tower downward into the boat. To Raise Cage -Lift the tower and swing up the rear legs. Install the four hand knobs. The threads in the aluminum foot could be damaged if the bolts are not aligned and threaded correctly. The Rad-A-Cage is designed to pull single (1) wakeboarder, trick skier, or kneeboarder. NOTE: Apply a thin coat of anti-seize to the threads of the hand knobs periodically. Rad-A-Cage Style 1 To Lower Cage For Storage Tools Required: 5/16” Allen Wrench 1.Loosen (but do not remove) the front 5/16-18 x 1-1/4” allen head bolts that connect the front legs to the foot. 2.Remove the hand knobs of the rear feet. 3. While standing in the bow area, pull the cage forward, gently placing it against the bow of the boat. Place padding between the cage and the boat to protect the gel coat finish from scratches. To Raise The Cage Lift and rock the tower back into place until the rear legs align with the rear feet. (Some manipulation of the cage may be required to get the legs to line up with the feet). Install both bolts and tighten all bolts. The threads in the aluminum foot could be damaged if the bolts are not aligned and threaded correctly! Rad-A-Cages are designed to pull one wakeboarder, kneeboarder or trick-skier. If your Supra model has been equipped with an optional RAD-A-CAGE towing tower, please review this section for details on it’s usage, maintenance and storage. The cage is designed as a stable tower to enhance wakeboarding. It is NOT intended to be used to tow skiers, barefoot skiers, or multiple wakeboarders. Such use will void any warranties written or implied. Before use, be sure that all mounting bolts are properly tightened in place. Be aware of ...
Questo manuale è adatto anche per i modelli :Barche - COMP LTS (1.46 mb)
Barche - LAUNCH 21 (1.46 mb)
Barche - LAUNCH 21V (1.46 mb)
Barche - LAUNCH 22SSV (1.46 mb)