Products that are replaced or for which a refund is issued become the property of Attwood. THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY OF THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1) YEAR FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or

Be sure to follow the applicable instructions. Every Wave Mast Float comes with the mounting bracket already installed to the float. All that remains to be done is to attach the mast float by following the proper installation to mast head instruction. 1. Hobie 14 with Comp Tip Mast Head. This mast uses the same mast head as the Hobie Wave. All that needs to be done is to remove the two clevis pins holding the two sheaves in place and replace them with the 2 each 10-32x1 1/2" machine screws. Rem

Always remember that the majority of water skiing injuries are the result of impacts with other objects. Always look where you are going and be aware of what is going on around you. Teak/Drag Surfing READ, UNDERSTAND and be FAMILIAR with the information contained on warning labels and adhere to the boat operation practices described on them. The United States Coast Guard issued a SAFETY ALERT on August 28, 2001 that covers some of the issues of improper use of the boarding platform. The SAFETY A

All other product names are copyright and registered trademarks/trade names of their respective owners. Skier’s Choice, Inc. reserves the right to change product specifications at any time without incurring obligation. © 2005 Skier’s Choice, Inc. Table of Contents Section I Introduction 3 Section II Boating Safety 5 Section III Boating Rules 11 Section IV Boat Specifications 15 Section V Operating Information 19 Section VI Starting & Operation 21 Section VII Instrument Panel 25 Sectioin VIII Equ

This will allow you to hook the track edge and pry out from under the lip. Be very carefull not to catch the lip and chip it. (A chipped lip will not hold the Luff track as well but does happen from time to time and may be no problem at alt.) Pry the corner away from the Comptip groove. Once again, Be carful not to chip the lip. Slide the screw driver deeper to hold the track away from the groove. Place the second screwdriver about 6 inches farther down the track and repeat the process. Repeat

Position pump in the lowest accessible part of the bilge. On sailboats, location should be centered over keel. (Figure 1) Thru-Hull Connector Hose & Clamp Hose MUST Rise Upward with NO DIPSuitable Mounting Pad Base Strainer 12" min. Above Water Line 2. Do not mount pump directly to hull. Attach base strainer to a marine plywood mounting pad that is fiberglassed to the hull. HOSE CONNECTION INSTRUCTIONS IMPORTANT: To prevent airlock, hose must rise continually upward to the thru-hull connector wi

Remember if your legs are too straight, you may strain your lower back. Some boats are equipped with thigh braces. For boats with easily adjusted Pull the blade alongside the kayak approximately to your hip and then lift paddle from the water braces, they should be fitted to transmit body movements directly to the kayak. The Power Stroke: The basic paddle technique is a forward stroke. Place the blade in the water near your toes. Pull the blade back alongside the kayak approximately to your hip–

extends the following limited warranty to the original retail consumer only (“Consumer”). WHAT DOES THIS WARRANTY COVER? This warranty covers material defects in workmanship and materials in your new Johnson Outdoors Paddle- sports products, with the exceptions stated below. Covered Paddlesports products include Ocean Kayak, Necky Kayaks, Old Town Canoes & Kayaks, Rogue River and Dimension products. HOW LONG COVERAGE LASTS. Ocean Kayak products: Three years from Consumer’s original purchase date

Cut out a patch large enough to overlap the damaged area by a minimum of 38 mm (1.5 in.) from all sides. Center the patch over the damaged area and with a pencil trace the outline of the patchApply masking tape around the perimeter of the outlined patch area to ensure a tight and clean glue line Using 100 grit sandpaper or a pumice stone, roughen the patch area on the boat as well as the backside of the patch. When sanding, you just need to rub off the protective outer surface of the fabric unti