Log:
valutazioni - 5, GPA: 4 ( )

Istruzioni per l'uso Attwood, Modello 3134

Produttore : Attwood
File Size : 478.55 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


If installing a combination light, place it on the furthermost tip of the bow on the centerline of the boat. (See Figure 1a.) If installing sidelights, the red lens must be on the port (left) and the green on the starboard (right) as you stand onboard facing the bow of the boat. (See Figure 1b.) Figure 1a Figure 1b 112.5° Arc Must Be Clear Green (Starboard) Red (Port) Red (Port) Green (Starboard) 2. Ensure that there are no front or side obstructions, such as rail stanchions, chocks, anchors, etc., within the arc of visibility (112.5° each side). certain that centerline of hole is aligned with boat centerline. Drill a 1-..." (29mm)-dia. hole. (See Figure 2.) Figure 2 (Applies to Quasar Light, not Snap Base) 13/16" (21mm) • 15/16" (24mm) • • FORWARD (14mm) (25mm) 2-1/4" (57mm) 1-1/8" (29mm) •• 9/16" • • 1" • • • MOUNTING INSTRUCTIONS 1. To access mounting holes inside the base: Loosen retaining screw one full turn; lift rear of cover, use flat base screwdriver if necessary to raise rear, rotate cover up and forward to unlock; twist lens counterclockwise and remove. 2. Place base into hole and align front and back with the boat centerline. Use base to mark pilot holes for the mounting screws. Drill pilot holes. 3. Feed the power source terminals up through the deck and attach to base terminals. Insulated terminals are recommended. CAUTION Position carefully on aluminum boats so that wires do not contact the hull. 4. Apply gasket (Attwood # 910467) or sealant to deck mounting area. Gasket is highly recommended on aluminum surfaces. Place base over the drilled holes. 5. Insert three stainless steel pan head mounting screws through base and fasten into deck. Replace lens, push cover down over front of lens lock - rotate back and down. Snap cover down into position and tighten the retaining screw. (See Figure 3.) Figure 3 Lock • • Lens Lock Detail • •• • • Festoon Bulb • • • Lock Catch Housing • Lock Lens Mounting Screws (Not Supplied) Screwdriver Slot 8-Watt Retaining Screw Boat Centerline Figure 3a (Optional Mount with Snap Base) Light Assembly Mounting Screws (Not Supplied) Connecting Posts Snap Base 1/4" or 1" (6mm or 25mm) Boat Centerline Forward (For ease of installation without disassembly of light.) WIRING INSTRUCTIONS The power source must be 12-volt DC ONLY. Use marine grade wire connectors only. Protect all connections with suitable materials. NOTE: Failure to make proper connections and fuse the light properly will void the product warranty. 1. Connect one terminal to the negative ( - ) post of the 12-volt battery. Connect the other terminal to the positive ( + ) lead through a 2-amp fuse and suitable dash-mounted switch. (See Figure 4.) Figure 4 Switch • 2-Amp Fuse • 2. Test lights for proper operation from dash-mounted control switch. MAINTENANCE Replace bulb, when necessary, with standard 8-watt automotive festoon type (Attwood #9230-7). Product Part Number 1/4" Snap Base 3300 (Black) 3301 (White) 3302 (Gray) 3304 (Cream) 1" Snap Base 33...

Questo manuale è adatto anche per i modelli :
Attrezzature per imbarcazioni - 3120 (478.55 kb)
Attrezzature per imbarcazioni - 3100 (478.55 kb)
Attrezzature per imbarcazioni - 3104 (478.55 kb)
Attrezzature per imbarcazioni - 3124 (478.55 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie